- 您現在的位置：買賣IC網 > PDF目錄10286 > LTC2440IGN (Linear Technology)IC ADC DIFFER 24-BIT HS 16-SSOP PDF資料下載
參數資料
| 型號： | LTC2440IGN |
| 廠商： | Linear Technology |
| 文件頁數： | 4/28頁 |
| 文件大小： | 0K |
| 描述： | IC ADC DIFFER 24-BIT HS 16-SSOP |
| 標準包裝： | 100 |
| 位數： | 24 |
| 采樣率（每秒）： | 3.5k |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 40mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，雙極 |
| 配用： | DC570A-ND - BOARD DELTA SIGMA ADC LTC2440 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC2440
12
2440fd
APPLICATIONS INFORMATION
microcontroller. Bit 31 (EOC) can be captured on the rst
rising edge of SCK. Bit 30 is shifted out of the device on
the rst falling edge of SCK. The nal data bit (Bit 0) is
shifted out on the falling edge of the 31st SCK and may
be latched on the rising edge of the 32nd SCK pulse. On
the falling edge of the 32nd SCK pulse, SDO goes HIGH
indicating the initiation of a new conversion cycle. This
bit serves as EOC (Bit 31) for the next conversion cycle.
Table 2 summarizes the output data format.
As long as the voltage on the IN+ and IN– pins is main-
tained within the –0.3V to (VCC + 0.3V) absolute maximum
operating range, a conversion result is generated for any
differential input voltage VIN from –FS = –0.5 VREF to
+FS = 0.5 VREF. For differential input voltages greater
than +FS, the conversion result is clamped to the value
corresponding to the +FS + 1LSB. For differential input
voltages below –FS, the conversion result is clamped to
the value corresponding to –FS – 1LSB.
SERIAL INTERFACE PINS
The LTC2440 transmits the conversion results and receives
the start of conversion command through a synchronous
2-wire, 3-wire or 4-wire interface. During the conversion
and sleep states, this interface can be used to assess
the converter status and during the data output state it
is used to read the conversion result and program the
speed/resolution.
Serial Clock Input/Output (SCK)
The serial clock signal present on SCK (Pin 13) is used to
synchronize the data transfer. Each bit of data is shifted out
the SDO pin on the falling edge of the serial clock.
In the Internal SCK mode of operation, the SCK pin is an
output and the LTC2440 creates its own serial clock. In
the External SCK mode of operation, the SCK pin is used
as input. The internal or external SCK mode is selected
by tying EXT (Pin 10) LOW for external SCK and HIGH
for internal SCK.
Serial Data Output (SDO)
The serial data output pin, SDO (Pin 12), provides the
result of the last conversion as a serial bit stream (MSB
rst) during the data output state. In addition, the SDO
pin is used as an end of conversion indicator during the
conversion and sleep states.
When CS (Pin 11) is HIGH, the SDO driver is switched
to a high impedance state. This allows sharing the serial
interface with other devices. If CS is LOW during the
convert or sleep state, SDO will output EOC. If CS is LOW
during the conversion phase, the EOC bit appears HIGH
on the SDO pin. Once the conversion is complete, EOC
goes LOW. The device remains in the sleep state until the
rst rising edge of SCK occurs while CS = LOW.
Table 2. LTC2440 Output Data Format
Differential Input Voltage
VIN*
Bit 31
EOC
Bit 30
DMY
Bit 29
SIG
Bit 28
MSB
Bit 27
Bit 26
Bit 25
…
Bit 0
VIN* ≥ 0.5 VREF**
0011000
…
0
0.5 VREF** – 1LSB
0
1
0
1
…
1
0.25 VREF**
0010100
…
0
0.25 VREF** – 1LSB
0
1
0
1
…
1
0
0010000
…
0
–1LSB
0001111
…
1
–0.25 VREF**
0001100
…
0
–0.25 VREF** – 1LSB
0
1
0
1
…
1
–0.5 VREF**
0001000
…
0
VIN* < –0.5 VREF**
0000111
…
1
*The differential input voltage VIN = IN+ – IN–. **The differential reference voltage VREF = REF+ – REF –.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2414CGN | IC ADC 8CH 24BIT DIFFINPUT28SSOP |
| MS27467T25B4SLC | CONN HSG PLUG 56POS STRGHT SCKT |
| LTC2415-1IGN#PBF | IC ADC 24BIT DIFFINPUT/REF16SSOP |
| D38999/26JJ61PALC | CONN HSG PLUG 61POS STRGHT PINS |
| LTC2415-1IGN | IC ADC 24BIT DIFFINPUT/REF16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2440IGN#PBF | 功能描述:IC ADC DIFFER 24-BIT HS 16-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2440IGN#PBF | 制造商:Linear Technology 功能描述:A/D Converter (A-D) IC 制造商:Linear Technology 功能描述:IC, ADC, 24BIT, 3.5KHZ, SSOP-16 |
| LTC2440IGN#TR | 功能描述:IC CONV A/D 24-BIT DIFF 16-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2440IGN#TRPBF | 功能描述:IC ADC DIFFER 24-BIT HS 16-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2440IGNPBF | 制造商:Linear Technology 功能描述:24-Bit Diff. ADC Speed/Resolution SSOP16 |
發布緊急采購，3分鐘左右您將得到回復。