參數資料
型號： LTC2377CMS-18#TRPBF
廠商： Linear Technology
文件頁數： 3/24頁
文件大?。?/td> 0K
描述： IC ADC 18BIT 500KSPS 16-DFN
產品培訓模塊： LTC2379- 18-/16-bit Fully-Differential SAR ADC Family Overview
標準包裝： 2,500
位數： 18
采樣率（每秒）： 500k
數據接口： 串行，SPI?
轉換器數目： 1
功率耗散（最大）： 8mW
電壓電源： 模擬和數字
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 16-TFSOP（0.118"，3.00mm 寬）
供應商設備封裝： 16-MSOP
包裝： 帶卷 (TR)
輸入數目和類型： 1 個差分，雙極
配用： DC1783A-G-ND - BOARD SAR ADC LTC2377-18
DC1783A-C-ND - BOARD SAR ADC LTC2377-16
LTC2377-18
11
237718f
APPLICATIONS INFORMATION
INPUT DRIVE CIRCUITS
A low impedance source can directly drive the high im-
pedance inputs of the LTC2377-18 without gain error. A
high impedance source should be buffered to minimize
settling time during acquisition and to optimize the dis-
tortion performance of the ADC. Minimizing settling time
is important even for DC inputs, because the ADC inputs
draw a current spike when entering acquisition.
For best performance, a buffer amplifier should be used
to drive the analog inputs of the LTC2377-18. The ampli-
fier provides low output impedance, which produces fast
settling of the analog signal during the acquisition phase.
It also provides isolation between the signal source and
the current spike the ADC inputs draw.
Input Filtering
The noise and distortion of the buffer amplifier and signal
source must be considered since they add to the ADC noise
and distortion. Noisy input signals should be filtered prior
to the buffer amplifier input with an appropriate filter to
minimize noise. The simple 1-pole RC lowpass filter (LPF1)
shown in Figure 4 is sufficient for many applications.
20Ω
3300pF
6600pF
20Ω
500Ω
LPF2
LPF1
BW = 600kHz
BW = 48kHz
SINGLE-ENDED-
TO-DIFFERENTIAL
DRIVER
SINGLE-ENDED-
INPUT SIGNAL
LTC2377-18
IN+
IN–
237718 F04
6800pF
High quality capacitors and resistors should be used in the
RC filters since these components can add distortion. NPO
and silver mica type dielectric capacitors have excellent
linearity. Carbon surface mount resistors can generate
distortion from self heating and from damage that may
occur during soldering. Metal film surface mount resistors
are much less susceptible to both problems.
Single-Ended-to-Differential Conversion
For single-ended input signals, a single-ended to differential
conversion circuit must be used to produce a differential
signal at the inputs of the LTC2377-18. The LT6350 ADC
driver is recommended for performing single-ended-to-
differential conversions. The LT6350 is flexible and may
be configured to convert single-ended signals of various
amplitudes to the ±5V differential input range of the
LTC2377-18. The LT6350 is also available in H-grade to
complement the extended temperature operation of the
LTC2377-18 up to 125°C.
Figure 5a shows the LT6350 being used to convert a 0V
to 5V single-ended input signal. In this case, the first
amplifier is configured as a unity gain buffer and the single-
ended input signal directly drives the high-impedance
input of the amplifier. As shown in the FFT of Figure 5b,
the LT6350 drives the LTC2377-18 to near full data sheet
performance.
The LT6350 can also be used to buffer and convert large
true bipolar signals which swing below ground to the
±5V differential input range of the LTC2377-18 in order
to maximize the signal swing that can be digitized. Fig-
ure6a shows the LT6350 being used to convert a ±10V
true bipolar signal for use by the LTC2377-18. In this
case, the first amplifier in the LT6350 is configured as
an inverting amplifier stage, which acts to attenuate and
level shift the input signal to the 0V to 5V input range of
the LTC2377-18. In the inverting amplifier configuration,
the single-ended input signal source no longer directly
drives a high impedance input of the first amplifier. The
input impedance is instead set by resistor RIN. RIN must
be chosen carefully based on the source impedance of the
signal source. Higher values of RIN tend to degrade both
the noise and distortion of the LT6350 and LTC2377-18
as a system.
Figure 4. Input Signal Chain
Another filter network consisting of LPF2 should be used
between the buffer and ADC input to both minimize the
noise contribution of the buffer and to help minimize distur-
bances reflected into the buffer from sampling transients.
Long RC time constants at the analog inputs will slow
down the settling of the analog inputs. Therefore, LPF2
requires a wider bandwidth than LPF1. A buffer amplifier
with a low noise density must be selected to minimize
degradation of the SNR.
相關PDF資料
PDF描述
VI-22R-IW-F2 CONVERTER MOD DC/DC 7.5V 100W
IDT72V02L25JI8 IC FIFO ASYNCH 1KX9 25NS 32PLCC
LT1328CS8#TRPBF IC RECEIVER 4MBPS IRDA IR 8-SOIC
MS3102A20-7SX CONN RCPT 8POS BOX MNT W/SCKT
IDT72V02L25JGI8 IC FIFO ASYNCH 1KX9 25NS 32PLCC
相關代理商/技術參數
參數描述
LTC2377CMS-20#PBF 制造商:Linear Technology 功能描述:IC ADC 20BIT 500KSPS 16MSOP 制造商:Linear Technology 功能描述:IC ADC 20BIT 500KSPS MSOP- 制造商:Linear Technology 功能描述:IC, ADC, 20BIT, 500KSPS, MSOP-16 制造商:Linear Technology 功能描述:MS-ADC/General Purpose, 20-Bit, 500ksps, 104dB SNR, 0.5pmm INL, 10.5mW, SAR ADC 制造商:Linear Technology 功能描述:ADC, 20BIT, 500KSPS, SPI, MSOP-16, Resolution (Bits):20bit, Sampling Rate:500kSPS, Supply Voltage Type:Single, Supply Voltage Min:2.375V, Supply Voltage Max:2.625V, Supply Current:4.2mA, Digital IC Case Style:MSOP, No. of Pins:16 , RoHS Compliant: Yes
LTC2377CMS-20#PBF 制造商:Linear Technology 功能描述:ADC 20BIT 500KSPS SPI MSOP 制造商:Linear Technology 功能描述:ADC 20BIT 500KSPS SPI MSOP-16
LTC2377CMS-20#TRPBF 制造商:Linear Technology 功能描述:IC ADC 20BIT 500KSPS 16MSOP 制造商:Linear Technology 功能描述:ADC, 20BIT, 500KSPS, SPI, MSOP-16, Resolution (Bits):20bit, Sampling Rate:500kSPS, Supply Voltage Type:Single, Supply Voltage Min:2.375V, Supply Voltage Max:2.625V, Supply Current:4.2mA, Digital IC Case Style:MSOP, No. of Pins:16 , RoHS Compliant: Yes 制造商:Linear Technology 功能描述:MS-ADC/General Purpose, 20-Bit, 500ksps, 104dB SNR, 0.5pmm INL, 10.5mW, SAR ADC
LTC2377HMS-16#PBF 功能描述:IC ADC 16BIT SPI 500KSPS 16MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
LTC2377HMS-16#TRPBF 功能描述:IC ADC 16BIT SPI 500KSPS 16MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*