- 您現在的位置：買賣IC網 > PDF目錄384633 > LTC2351IUH-14 (LINEAR TECHNOLOGY CORP) Channel, 14-Bit, 1.5Msps Simultaneous Sampling ADC with Shutdown PDF資料下載
參數資料
| 型號： | LTC2351IUH-14 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | Channel, 14-Bit, 1.5Msps Simultaneous Sampling ADC with Shutdown |
| 中文描述： | 6-CH 14-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, PQCC32 |
| 封裝： | 5 X 5 MM, PLASTIC, MO-220WHHD, QFN-32 |
| 文件頁數： | 14/20頁 |
| 文件大?。?/td> | 279K |
| 代理商： | LTC2351IUH-14 |
14
LTC2351-14
235114f
APPLICATIOU
INPUT FILTERING AND SOURCE IMPEDANCE
The noise and the distortion of the input amplifier and
other circuitry must be considered since they will add to
the LTC2351-14 noise and distortion. The small-signal
bandwidth of the sample-and-hold circuit is 50MHz. Any
noise or distortion products that are present at the analog
inputs will be summed over this entire bandwidth. Noisy
input circuitry should be filtered prior to the analog inputs.
A simple 1-pole RC filter is sufficient for many applica-
tions. For example, Figure 1 shows a 47pF capacitor from
CHO
+
to ground and a 51
source resistor to limit the net
input bandwidth to 30MHz. The 47pF capacitor also acts
as a charge reservoir for the input sample-and-hold and
isolates the ADC input from sampling-glitch sensitive cir-
cuitry. High quality capacitors and resistors should be
used since these components can add distortion. NPO and
silvermica type dielectric capacitors have excellent linear-
ity. Carbon surface mount resistors can generate distor-
tion from self heating and from damage that may occur
during soldering. Metal film surface mount resistors are
much less susceptible to both problems. When high am-
plitude unwanted signals are close in frequency to the
desired signal frequency a multiple pole filter is required.
High external source resistance, combined with 13pF of
input capacitance, will reduce the rated 50MHz input band-
width and increase acquisition time beyond 39ns.
W
U
U
INPUT RANGE
The analog inputs of the LTC2351-14 may be driven fully
differentially with a single supply. Either input may swing
up to V
CC
, provided the differential swing is no greater than
2.5V with BIP (Pin 29) Low, or
±
1.25V with (BIP Pin 29)
High. The 0V to 2.5V range is also ideally suited for single-
ended input use with single supply applications. The
common mode range of the inputs extend from ground to
the supply voltage V
CC
. If the difference between the CH
+
and CH
–
at any input pair exceeds 2.5V (unipolar) or 1.25V
(bipolar), the output code will stay fixed at positive full-
scale, and if this difference goes below 0V (unipolar) or
–1.25V (bipolar), the output code will stay fixed at negative
full-scale.
INTERNAL REFERENCE
The LTC2351-14 has an on-chip, temperature compen-
sated, bandgap reference that is factory trimmed to 2.5V
to obtain a precise 2.5V input span. The reference ampli-
fier output V
REF
, (Pin 23) must be bypassed with a capaci-
tor to ground. The reference amplifier is stable with capaci-
tors of 1
μ
F or greater. For the best noise performance, a
10
μ
F ceramic or a 10
μ
F tantalum in parallel with a 0.1
μ
F
ceramic is recommended. The V
REF
pin can be overdriven
with an external reference as shown in Figure 2. The volt-
age of the external reference must be higher than the 2.5V
of the open-drain P-channel output of the internal refer-
ence. The recommended range for an external reference
is 2.55V to V
DD
. An external reference at 2.55V will see a
DC quiescent load of 0.75mA and as much as 3mA
during conversion.
Figure 1. RC Input Filter
LTC2351-14
CH0
+
CH0
–
V
REF
GND
235114 F01
1
2
11
3
10
μ
F
47pF*
51
*
CH1
+
CH1
–
4
5
47pF*
*TIGHT TOLERANCE REQUIRED TO AVOID
APERTURE SKEW DEGRADATION
51
*
ANALOG
INPUT
ANALOG
INPUT
Figure 2. External Reference
LTC2351-14
V
REF
GND
235114 F02
23
22
10
μ
F
LT1790-3
3.5V to 18V
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2421 | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| LTC2422 | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| LTUX | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| LTUY | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
| LTUZ | 1-/2-Channel 20-Bit UPower No Latency ADCs in MSOP-10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2351IUH-14#PBF | 功能描述:IC ADC 14BIT 1.5MSPS 32-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2351IUH-14#TRPBF | 功能描述:IC ADC 14BIT 1.5MSPS 32-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC2351IUH-14PBF | 制造商:Linear Technology 功能描述:ADC 1.5Msps 14-Bit Serial QFN32EP |
| LTC2355CMSE-12#PBF | 功能描述:IC ADC 12BIT 3.5MSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2355CMSE-12#TRPBF | 功能描述:IC ADC 12BIT 3.5MSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。