AIN1+ (Pin 1): Channel 1 Positive Diffe" />
參數資料
型號： LTC2172IUKG-14#PBF
廠商： Linear Technology
文件頁數： 9/34頁
文件大小： 0K
描述： IC ADC 14BIT SER/PAR 65M 52-QFN
標準包裝： 45
位數： 14
采樣率（每秒）： 65M
數據接口： Serial LVDS
轉換器數目： 4
功率耗散（最大）： 419mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 52-WFQFN 裸露焊盤
供應商設備封裝： 52-QFN（7x8）
包裝： 管件
輸入數目和類型： 2 Differential; 2 Single-Ended
配用： DC1371A-ND - BOARD USB DATA ACQUISITION HS
LTC2172-14/
LTC2171-14/LTC2170-14
17
21721014fb
AIN1+ (Pin 1): Channel 1 Positive Differential Analog
Input.
AIN1– (Pin 2): Channel 1 Negative Differential Analog
Input.
VCM12 (Pin 3): Common Mode Bias Output, Nominally
Equal to VDD/2. VCM should be used to bias the common
mode of the analog inputs of channels 1 and 2. Bypass
to ground with a 0.1F ceramic capacitor.
AIN2+ (Pin 4): Channel 2 Positive Differential Analog
Input.
AIN2– (Pin 5): Channel 2 Negative Differential Analog
Input.
REFH (Pins 6, 7): ADC High Reference. Bypass to Pin 8
and Pin 9 with a 2.2F ceramic capacitor, and to ground
with a 0.1F ceramic capacitor.
REFL (Pins 8, 9): ADC Low Reference. Bypass to Pin 6
and Pin 7 with a 2.2F ceramic capacitor, and to ground
with a 0.1F ceramic capacitor.
AIN3+ (Pin 10): Channel 3 Positive Differential Analog
Input.
AIN3– (Pin 11): Channel 3 Negative Differential Analog
Input.
VCM34 (Pin 12): Common Mode Bias Output, Nominally
Equal to VDD/2. VCM should be used to bias the common
mode of the analog inputs of channels 3 and 4. Bypass
to ground with a 0.1F ceramic capacitor.
AIN4+ (Pin 13): Channel 4 Positive Differential Analog
Input.
AIN4– (Pin 14): Channel 4 Negative Differential Analog
Input.
VDD (Pins 15, 16, 51, 52): 1.8V Analog Power Supply.
Bypass to ground with 0.1F ceramic capacitors. Adjacent
pins can share a bypass capacitor.
ENC+ (Pin 17): Encode Input. Conversion starts on the
rising edge.
ENC– (Pin 18): Encode Complement Input. Conversion
starts on the falling edge.
CS(Pin19):Inserialprogrammingmode(PAR/SER=0V),
CS is the serial interface chip select input. When CS is low,
SCK is enabled for shifting data on SDI into the mode
controlregisters.Inparallelprogrammingmode(PAR/SER
= VDD), CS selects two-lane or one-lane output mode. CS
can be driven with 1.8V to 3.3V logic.
SCK (Pin 20): In serial programming mode (PAR/SER
= 0V), SCK is the serial interface clock input. In parallel
programming mode (PAR/SER = VDD),SCKselects3.5mA
or 1.75mA LVDS output currents. SCK can be driven with
1.8V to 3.3V logic.
SDI (Pin 21): In serial programming mode (PAR/SER =
0V), SDI is the serial interface data input. Data on SDI
is clocked into the mode control registers on the rising
edge of SCK. In parallel programming mode (PAR/SER =
VDD), SDI can be used to power down the part. SDI can
be driven with 1.8V to 3.3V logic.
GND (Pins 22, 45, 49, Exposed Pad Pin 53): ADC Power
Ground. The exposed pad must be soldered to the PCB
ground.
OGND (Pin 33): Output Driver Ground. Must be shorted
to the ground plane by a very low inductance path. Use
multiple vias close to the pin.
OVDD (Pin 34): Output Driver Supply. Bypass to ground
with a 0.1F ceramic capacitor.
SDO (Pin 46): In serial programming mode (PAR/SER
= 0V), SDO is the optional serial interface data output.
Data on SDO is read back from the mode control registers
and can be latched on the falling edge of SCK. SDO is
an open-drain N-channel MOSFET output that requires
an external 2k pull-up resistor of 1.8V to 3.3V. If read-
back from the mode control registers is not needed,
the pull-up resistor is not necessary and SDO can be
left unconnected. In parallel programming mode (PAR/
SER = VDD), SDO is an input that enables internal 100
termination resistors on the digital outputs. When used
as an input, SDO can be driven with 1.8V to 3.3V logic
through a 1k series resistor.
pin FuncTions
相關PDF資料
PDF描述
VI-JTN-MY-F4 CONVERTER MOD DC/DC 18.5V 50W
MAX970EEE+T IC COMPARATOR R-R 16-QSOP
MAX490CSA+ IC TXRX RS485/RS422 LOWPWR 8SOIC
LTC2261IUJ-14#PBF IC ADC 14-BIT 125MSPS 40-QFN
MAX970EEE-T IC COMPARATR QUAD R-R I/O 16QSOP
相關代理商/技術參數
參數描述
LTC2172IUKG-14TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 65Msps/40Msps/25Msps Low Power Quad ADCs
LTC2173-12 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 125Msps/105Msps/ 80Msps Low Power Octal ADCs
LTC2173-14 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 125Msps/105Msps/ 80Msps Low Power Octal ADCs
LTC2173CUKG-12#PBF 功能描述:IC ADC 12BIT SER 80MSPS 52-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
LTC2173CUKG-12#TRPBF 功能描述:IC ADC 12BIT 80MSPS QUAD 52QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*