- 您現在的位置：買賣IC網 > PDF目錄11772 > LTC1756EGN (Linear Technology)IC SMART CARD 16-SSOP PDF資料下載
參數資料
| 型號： | LTC1756EGN |
| 廠商： | Linear Technology |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SMART CARD 16-SSOP |
| 標準包裝： | 100 |
| 應用： | 智能卡 |
| 電源電壓： | 2.7 V ~ 6 V |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SSOP |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
| 其它名稱： | Q1274157 |
8
LTC1755/LTC1756
microseconds then the LTC1755/LTC1756 switch to the
Alarm state. This fault checking is only performed after the
VCC pin has reached its final value (as indicated by the
READY pin).
The clock channel is optimized for signal integrity in order
to meet the stringent duty cycle requirements of the EMV
specification. Therefore, to reduce power in low power
applications, clock stop mode is recommended when data
is not being exchanged.
CIN (Pins 13/9): (Input) Clock Input Pin from the Micro-
controller. During the Active state this signal appears on
the CLK pin after being level-shifted and buffered.
DVCC sets the logic reference level for the CIN pin.
RIN (Pins 14/10): (Input) Reset Input Pin from the Micro-
controller. During the Active state this signal appears on
the RST pin after being level-shifted and buffered.
DVCC sets the logic reference level for the RIN pin.
DATA (Pins 15/11): (Input/Output) Microcontroller Side
Data I/O Pin. This pin is used for bidirectional data transfer
between the microcontroller and the Smart Card. The
microcontroller data pin must be open drain and must be
able to sink up to 250
A when driving the DATA pin low
due to the pull-up current source. The DATA pin becomes
high impedance during the Idle state or when CS is high
(see the State Diagram). It does not become active until the
READY signal goes low indicating that VCC is stable.
AUX2IN (Pin 16, LTC1755 Only): (Input/Output) Micro-
controller Side Auxiliary I/O pin. This pin is used for
bidirectional auxiliary data transfer between the micro-
controller and the Smart Card. It has the same character-
istics as the DATA pin.
AUX1IN (Pin 17, LTC1755 Only): (Input/Output) Micro-
controller Side Auxiliary I/O Pin. This pin is used for
bidirectional auxiliary data transfer between the micro-
controller and the Smart Card. It has the same character-
istics as the DATA pin.
C+, C– (Pins 18/12, 19/13): Charge Pump Flying Capaci-
tor Terminals. Optimum values for the flying capacitor
range from 0.68
F to 1F. Best performance is achieved
with a low ESR X7R ceramic capacitor.
DVCC (Pin 20, LTC1755 Only): Supply Voltage for the
Microcontroller Side Digital Input and Input/Output Pins
(Typically 3V). If the charge pump input pin (VIN) is
powered from the same source as the microcontroller,
then DVCC should be connected directly to VIN. In this case
only one (10
F) input bypass capacitor is needed for the
LTC1755. If the DVCC pin is powered separately then it
should be bypassed separately with a 0.1
F capacitor. The
DVCC pin may be between 2V and 5.5V.
The DVCC pin is monitored for adequate voltage. If DVCC
drops below approximately 1.5V the LTC1755 automati-
cally enters the Idle state. On the LTC1756, DVCC is
connected internally to VIN.
READY (Pins 21/14): (Output) Readiness Indicator of the
Smart Card Supply Voltage (VCC). When the LTC1755/
LTC1756 are placed in the Active state the soft-start
feature slowly ramps the VCC voltage. A low on the READY
pin indicates that VCC has reached its final value.
The READY pin also indicates if the LTC1756 is in Alarm
mode. The LTC1756 detects faults such as VCCunderrange
for at least 5
s, overtemperature shutdown, CLK or RST
invalid output levels and card removal during Active
state. CLK or RST invalid and overtemperature faults are
detected only after VCC has reached its final value. VCC
underrange and card removal during Active faults are
detected at any time during the Active period (i.e., once
PWR = 0V).
If the LTC1756 has been activated normally and VCC, the
card voltage, has reached its final value then READY will
go low indicating normal operation. If, following this, a
fault occurs and the LTC1756 enters the Alarm state, the
READY pin will return high.
In the event that a fault precedes the activation of VCC,
such as a direct short circuit from VCC to GND, the
LTC1756 will attempt to operate until the fault is detected
and then automatically shut down and enter the Alarm
state. In this case the READY pin will never go low after the
command to start the smart card is given (i.e., PWR = 0V).
If the LTC1755/LTC1756 enter the Alarm state they can
only be cleared by returning the PWR pin high.
UU
U
PI FU CTIO S LTC1755/LTC1756
相關PDF資料 |
PDF描述 |
|---|---|
| V150C12H150BF2 | CONVERTER MOD DC/DC 12V 150W |
| MS27468T17B35H | CONN RCPT 55POS JAM NUT W/PINS |
| PIC12F1840-E/P | MCU 7KB FLASH 256B RAM XLP 8PDIP |
| V150C12H150BL3 | CONVERTER MOD DC/DC 12V 150W |
| D38999/20JB98SD | CONN RCPT 6POS WALL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1756EGN#PBF | 功能描述:IC SMART CARD INTERFACE 16SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| LTC1756EGN#TR | 功能描述:IC SMART CARD INTERFACE 16SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| LTC1756EGN#TRPBF | 功能描述:IC SMART CARD INTERFACE 16SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| LTC1757A-1EMS8 | 功能描述:IC CTRLR RF POWER SINGLE 8MSOP RoHS:否 類別:RF/IF 和 RFID >> RF 電源控制器 IC 系列:- 標準包裝:3,000 系列:- RF 型:GSM 頻率:450MHz ~ 2GHz 特點:四頻帶 封裝/外殼:8-VFBGA 供應商設備封裝:8-MicroSMD（1.51x1.51） 包裝:帶卷 (TR) 其它名稱:LMV243BLX |
| LTC1757A-1EMS8#PBF | 功能描述:IC CTRLR RF POWER SINGLE 8MSOP RoHS:是 類別:RF/IF 和 RFID >> RF 電源控制器 IC 系列:- 標準包裝:3,000 系列:- RF 型:GSM 頻率:450MHz ~ 2GHz 特點:四頻帶 封裝/外殼:8-VFBGA 供應商設備封裝:8-MicroSMD（1.51x1.51） 包裝:帶卷 (TR) 其它名稱:LMV243BLX |
發布緊急采購，3分鐘左右您將得到回復。