參數資料
型號: LTC1703
廠商: Linear Technology Corporation
元件分類: 通用總線功能
英文描述: Synchronous 8-Bit Up/Down Binary Counters 24-PDIP 0 to 70
中文描述: 雙550kHz的同步二相開關穩壓控制器5位VID
文件頁數: 6/36頁
文件大?。?/td> 343K
代理商: LTC1703
6
LTC1703
VIDnpin includes an on-chip 40k
pull-up resistor in
series with a diode (see Block Diagram).
V
CC
(Pin 18):
Power Supply Input. All internal circuits
except the output drivers are powered from this pin. V
CC
should be connected to a low noise power supply voltage
between 3V and 7V and should be bypassed to SGND with
at least a 1
μ
F capacitor in close proximity to the LTC1703.
FB2 (Pin 19):
Controller 2 Feedback Input. FB2 should be
connected through a resistor divider network to V
OUT2
to
set the ouput voltage. The loop compensation network for
controller 2 also connects to FB2.
COMP2 (Pin 20):
Controller 2 Loop Compensation. See
COMP1.
RUN/SS2 (Pin 21):
Controller 2 Run/Soft-Start. See RUN/
SS1.
FAULT (Pin 22):
Output Overvoltage Fault (Latched). The
FAULT pin is an open-drain output with an internal 10
μ
A
pull-up. If either regulated output voltage rises more than
15% above its programmed value for more than 25
μ
s, the
FAULT output will go high and the entire LTC1703 will be
disabled. When FAULT is high, both BG pins will go high,
turning on the bottom MOSFET switches and pulling down
the high output voltage. The LTC1703 will remain latched
in this state until the power is cycled. When FAULT mode
is active, the FAULT pin will be pulled up with an internal
10
μ
A current source. Tying FAULT directly to SGND will
disable latched FAULT mode and will allow the LTC1703 to
resume normal operation when the overvoltage fault is
removed.
PGND (Pin 23):
Power Ground. The BGndrivers return to
this pin. Connect PGND to a high current ground node in
close proximity to the sources of external MOSFETs, QB1
and QB2, and the V
IN
and V
OUT
bypass capacitors.
SW2 (Pin 24):
Controller 2 Switching Node. See SW1.
TG2 (Pin 25):
Controller 2 Top Gate Drive. See TG1.
BG2 (Pin 26):
Controller 2 Bottom Gate Drive. See BG1.
BOOST2 (Pin 27):
Controller 2 Top Gate Driver Supply.
See BOOST1.
I
MAX2
(Pin 28):
Controller 2 Current Limit Set. See I
MAX1
.
V
CC
5V
2k
2000pF
NC
NC
NC
2000pF
2000pF
2000pF
BOOST1
TG1
BG1
SW1
I
MAX1
FCB
VID0:4
RUN/SS1
COMP1
FB1
SENSE
LTC1703
BOOST2
TG2
BG2
SW2
I
MAX2
FAULT
RUN/SS2
COMP2
FB2
0.1
μ
F
100
μ
F
V
FB1
V
FB2
V
FAULT
I
BOOST1
I
CC
I
PVCC
I
BOOST2
f
MEASURED
1703 TC
PV
CC
GND
PGND
+
2k
Test Circuit 1
PIU
TEST CIRCUIT
相關PDF資料
PDF描述
LTC1703CG Synchronous 8-Bit Up/Down Binary Counters 24-PDIP 0 to 70
LTC1704 Synchronous 8-Bit Up/Down Binary Counters 24-SOIC 0 to 70
LTC1704B Synchronous 8-Bit Up/Down Binary Counters 24-SOIC 0 to 70
LTC1705 Dual 550kHz Synchronous Switching Regulator Controller with 5-Bit VID and 150mA LDO
LTC1705EGN Dual 550kHz Synchronous Switching Regulator Controller with 5-Bit VID and 150mA LDO
相關代理商/技術參數
參數描述
LTC1703CG 功能描述:IC REG SW DUAL SYNC VID 28SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器,Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN(7x7) 包裝:管件
LTC1703CG#PBF 功能描述:IC REG SW DUAL SYNC VID 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器,DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP(0.173",4.40mm 寬) 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR)
LTC1703CG#TR 制造商:Linear Technology 功能描述:LDO Cntrlr REG CTRLR 0.9V to 2V 28-Pin SSOP T/R
LTC1703CG#TRPBF 功能描述:IC REG SW DUAL SYNC VID 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器,Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN(7x7) 包裝:管件
LTC1703IG 功能描述:IC REG SW DL SYNC W/VID 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器,Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN(7x7) 包裝:管件