參數資料
型號: LTC1643AL-1CGN#PBF
廠商: Linear Technology
文件頁數: 9/16頁
文件大小: 236K
描述: IC CTRLR HOTSWAP PCI BUS 16SSOP
標準包裝: 100
類型: 熱交換控制器
應用: CompactPCI?
內部開關:
電源電壓: 3.3V,5V,±12V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 16-SSOP(0.154",3.90mm 寬)
供應商設備封裝: 16-SSOP
包裝: 管件
9
LTC1643AL
LTC1643AL-1/LTC1643AH
 1643afb
LTC1643A FEATURE SUMMARY
1. Allows safe board insertion and removal from either a
motherboard (LTC1643AH) or CompactPCI board
(LTC1643AL/LTC1643AL-1).
2. Controls all four PCI supplies: 12V, 12V, 3.3V and 5V.
3. Programmable foldback current limit: a programmable
analog current limit with a value that depends on the
output voltage. If the output is shorted to ground, the
current limit drops to keep power dissipation and
supply glitches to a minimum.
4. Programmable circuit breaker: if a supply remains in
current limit too long, the circuit breaker will trip, the
supplies will be turned off and the FAULT pin pulled low.
5. Current limit power-up: the supplies are allowed to
power up in current limit. Allows the chip to power up
boards with widely varying capacitive loads without
tripping the circuit breaker. The maximum allowable
power-up time is programmable using the TIMER pin.
6. 12V and 12V power switches on chip.
7. Power good output: monitors the voltage status of the
four supply voltages, except the LTC1643AL-1 which
only monitors 3V
OUT
 and 5V
OUT
.
8. Space saving 16-pin SSOP package.
PCI Power Requirements
PCI systems usually require four power rails: 5V, 3.3V,
12V and 12V. Systems implementing the 3.3V signaling
environment are usually required to provide all four rails in
every system. Systems implementing the 5V signaling
environment may either ship the 3.3V supply with the
system or provide a means to add it afterward. The
tolerance of the supplies as measured at the components
on the plug-in card is summarized in Table 1.
APPLICATIONS INFORMATION
U
U
U
Some ?2V supplies in CompactPCI applications are not
well regulated and can violate the tolerance specification.
For these applications, the LTC1643AL-1 should be used
because the PWRGD signal does not depend on ?2V
outputs.
Power-Up Sequence
The power supplies are controlled by placing external
N-channel pass transistors in the 3.3V and 5V power
paths, and internal pass transistors for the 12V and 12V
power paths (Figure 1).
Resistors R1 and R2 provide current fault detection and
R7 and C1 provide current control loop compensation.
Resistors R5 and R6 prevent high frequency oscillations
in Q1 and Q2.
When the ON pin (Pin 5) is pulled high, the pass transistors
are allowed to turn on and a 22礎 current source is
connected to the TIMER pin (Pin 4) (Figure 2).
The current in each pass transistor increases until it
reaches the current limit for each supply. Each supply is
then allowed to power up at the rate dv/dt = 62礎/C1 or as
determined by the current limit and the load capacitance
whichever is slower. Current limit faults are ignored while
the TIMER pin (Pin 4) voltage is ramping up and is less
than 0.9V below 12V
IN
  (Pin 1). Once all four supply
voltages are within tolerance, the PWRGD pin (Pin 7) will
pull low.
Power-Down Sequence
When the ON pin (Pin 5) is pulled low, a power-down
sequence begins (Figure 3).
Internal switches are connected to each of the output
supply voltage pins to discharge the bypass capacitors to
ground. The TIMER pin (Pin 4) is immediately pulled low.
The GATE pin (Pin 11) is pulled down by a 200礎 current
source to prevent the load currents on the 3.3V and 5V
supplies from going to zero instantaneously and glitching
the power supply voltages. When any of the output
voltages dip below its threshold, the PWRGD pin (Pin 7)
pulls high.
Table 1. PCI Power Supply Requirements
CAPACITIVE
SUPPLY
TOLERANCE
LOAD
5V
5V ?%
<3000礔
3.3V
3.3V ?.3V
<3000礔
12V
12V ?%
<500礔
12V
12V ?0%
<120礔
相關PDF資料
PDF描述
LTC1644CGN#TRPBF IC CONTROLLER HOT SWAP 20-SSOP
LTC1645IS#TRPBF IC CTRLR SEQ HOTSWAP DUAL 14SOIC
LTC1646IGN#TR IC CNTRLR HOTSWAP PCIDUAL 16SSOP
LTC1647-1IS8#TRPBF IC CONTROLLR HOTSWAP DUAL 8-SOIC
LTC1704EGN#TRPBF IC REG DL BUCK/LINEAR 16SSOP
相關代理商/技術參數
參數描述
LTC1643AL-1IGN 功能描述:IC CTRLR HOTSWAP PCI BUS 16SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型,PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V,12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP(12x12) 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC1643AL-1IGN#PBF 功能描述:IC CTRLR HOTSWAP PCI BUS 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型,PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V,12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP(12x12) 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC1643AL-1IGN#TR 功能描述:IC CTRLR HOTSWAP PCI BUS 16SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型,PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V,12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP(12x12) 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC1643AL-1IGN#TRPBF 功能描述:IC CTRLR HOTSWAP PCI BUS 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型,PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V,12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP(12x12) 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC1643AL-1IGNPBF 制造商:Linear Technology 功能描述:PCI-Bus Hot Swap Controller, LTC1643AL