- 您現在的位置：買賣IC網 > PDF目錄385505 > LTC1559-5 (Linear Technology Corporation) Backup Battery Controller with Fixed Output(帶固定輸出后備電池控制器) PDF資料下載
參數資料
| 型號： | LTC1559-5 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Backup Battery Controller with Fixed Output(帶固定輸出后備電池控制器) |
| 中文描述： | 備用電池控制器（帶固定輸出后備電池控制器具有固定輸出） |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 290K |
| 代理商： | LTC1559-5 |
5
LTC1559-3.3/LTC1559-5
PI
FU
CTIO
N
S
U
U
Pin Numbers Are Shown First for the SO-8 Package
Then the GN16 and S16 Packages
SW (Pins 1/1, 2):
Boost Converter Switching Node. Con-
nect a 22
μ
H inductor from SW to the positive terminal of
the backup cell. In backup mode, this node is alternately
switched between ground and V
BAK
, generating the backup
output voltage. In fast or trickle charge mode, an internal
regulator outputs a constant DC current from this pin
through the 22
μ
H inductor and into the NiCd battery.
During power-up or undervoltage lockout (UVLO), the SW
pin enters a high impedance state.
GND (Pins 2/4):
System Ground. The low power internal
circuitry returns to this pin in the 16-pin packages. GND
and PGND are bonded together to this pin in the 8-pin
package.
CTL (Pins 3/5):
Control. This pin provides three functions.
In backup mode this pin is a high impedance input and
monitors the backup battery cell voltage (V
BAT
). If V
BAT
drops below 0.9V, the LTC1559 enters UVLO. During
trickle charge mode, an external resistor R
EXT
sets the
trickle charge current. In all modes, pulling the CTL pin
below 250mV generates either a “soft” or “hard” reset
pulse. See the Applications Information section for more
information.
PS (Pins 4/7):
Power Supply Sense. This pin senses the
presence of the main supply and triggers the LTC1559 to
terminate backup mode. During backup, V
CC
is driven
externally by the LTC1559’s boost convert’s output (V
BAK
).
When PS > V
CC
during backup, the LTC1559 pulls down
the BACKUP pin, reconnecting the system regulator out-
put to the system V
CC
. The PS pin is needed in applications
that use a P-channel MOSFET (driven by the BACKUP
signal) to isolate the system regulator during backup. If
not needed, PS can be disabled by tying it to ground.
RESET (Pins 5/11):
System Reset, Active Low. This is an
open-drain output. This pin provides a low going reset
signal to the system processor. A 200ms pulse is gener-
ated if the CTL pin is pulled low for more than two seconds
(“hard” reset) or if the LTC1559 comes out of UVLO. This
“hard reset” stops the internal boost converter if it is
running. This pin is held low if the LTC1559 is in UVLO and
is guaranteed to be valid when V
CC
is greater than or equal
to 1V.
RESET also provides a low going 100
μ
s signal whenever
the CTL pin is pulled low for less than two seconds (“soft”
reset). Unlike hard reset, soft reset does not affect the
LTC1559’s current operating mode.
BACKUP (Pins 6/13):
System Backup Signal. This is a
TTL-compatible output driver that pulls low unless the
LTC1559 is in backup mode. BACKUP signals the system
controller that the system is in backup mode so that it can
reduce system loading. BACKUP can also be used to drive
the gate of a P-channel MOSFET in series with the main
system regulator’s output. See the Applications Informa-
tion section for more details.
V
CC
(Pins 7/14):
Power Supply Input. All internal circuits
except the boost converter are powered from this pin. A
0.1
μ
F bypass capacitor is required from V
CC
to ground.
The UVLO detector inside the LTC1559 monitors V
CC
. If
V
CC
drops below the rated output voltage by 9%, the
LTC1559 enters UVLO mode and RESET is asserted. The
LTC1559-3.3 exits UVLO if V
CC
rises to greater than
–5.5% of the rated output voltage. The LTC1559-5 exits
UVLO if V
CC
rises to greater than –6% of the rated output
voltage. See the Applications Information section for more
details.
V
BAK
(Pins 8/15, 16):
Backup Supply Output. The LTC1559’s
boost converter provides the regulated output voltage to
the system through V
BAK
during backup mode.
16-Pin GN and SO Packages
PGND (Pin 3):
Power Ground. The internal driver circuitry
returns to this pin. PGND should be connected to a low
impedance ground plane in close proximity to the NiCd
battery cell.
SHDN (Pin 6):
Chip Shutdown. A TTL-compatible active
low voltage at SHDN puts the LTC1559 into low power
shutdown mode. In shutdown, all internal circuits power
down and are held in a reset state. The SW, CTL and V
BAK
pins enter into high impedance states. In shutdown mode,
supply current drops to below 50
μ
A and current drawn
from the backup cell drops to below 15
μ
A.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1560-1 | 1MHz/500kHz Continuous Time, Low Noise, Lowpass Elliptic Filter |
| LTC1560-1C | Advanced,Self-Calibrating, Precision, Dual Operational Amplifier 20-LCCC -55 to 125 |
| LTC1560-1CS8 | 1MHz/500kHz Continuous Time, Low Noise, Lowpass Elliptic Filter |
| LTC1560-1I | Advanced,Self-Calibrating, Precision, Dual Operational Amplifier 8-CDIP -55 to 125 |
| LTC1560-1IS8 | Advanced,Self-Calibrating, Precision, Dual Operational Amplifier 10-CFP -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1559CGN-3.3 | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| LTC1559CGN-3.3#PBF | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| LTC1559CGN-3.3#TRPBF | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| LTC1559CGN-5 | 功能描述:IC BACKUP BATT CNTRLR 5V 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| LTC1559CGN-5#PBF | 功能描述:IC BACKUP BATT CNTRLR 5V 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
發布緊急采購，3分鐘左右您將得到回復。