- 您現在的位置：買賣IC網 > Datasheet目錄41 > LTC1422CN8 (Linear Technology)IC CONTROLLER HOT SWAP 8-DIP Datasheet資料下載
參數資料
| 型號： | LTC1422CN8 |
| 廠商： | Linear Technology |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 197K |
| 描述： | IC CONTROLLER HOT SWAP 8-DIP |
| 標準包裝： | 50 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 2.7 V ~ 12 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 8-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 8-PDIP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1341 (CN2011-ZH PDF) |
9
LTC1422
1422fb
APPLICATIONS INFORMATION
U
U
U
When the timer is off, the internal N-channel Q1 shorts the
TIMER pin to ground. When the timer is turned on, a 2礎
current from V
CC
is connected to the TIMER pin and the
voltage on the external capacitor C2 starts to ramp up with
a slope given by: dV/dt = 2礎/C2. When the voltage
reaches the trip point (1.232V), the timer will be reset by
pulling the TIMER pin back to ground. The timer period is
given by: (1.232V " C2)/2礎. For a 200ms delay, use a
0.33礔 capacitor.
Electronic Circuit Breaker
The LTC1422 features an electronic circuit breaker func-
tion that protects against short circuits or excessive cur-
rents on the supply. By placing a sense resistor between
the supply input and SENSE pin, the circuit breaker will be
tripped whenever the voltage across the sense resistor is
greater than 50mV for more than 10祍. When the circuit
breaker trips, the GATE pin is immediately pulled to
ground and the external N-channel is quickly turned off.
When the ON pin is cycled off for greater than 40祍 and
then on as shown in Figure 7, time point 7, the circuit
breaker is reset and another timing cycle is started.
At the end of the timer cycle (time point 8), the charge
pump will turn on again. If the circuit breaker feature is not
required, the SENSE pin should be shorted to V
CC
.
If more than 10祍 of response time is needed to reject
supply noise, an external resistor and capacitor can be
added to the sense circuit as shown in Figure 8.
Connection Sense with ON Pin
The ON pin can be used to sense board connection to the
backplane as shown in Figure 9.
Using staggered connection pins, ground mates first to
discharge any static build up on the board, followed by the
V
CC
connection and all other pins. When V
CC
makes
connection, the bases of transistors Q3 and Q4 are pulled
high turning them on and pulling the ON pin to ground.
When the base connector pins of Q3 and Q4 finally mate
to the backplane, the bases are shorted to ground. This
turns off Q3 and Q4 and allows the ON pin to pull high and
start a power-up cycle. The base connection pins of Q3 and
Q4 should be located at opposite ends of the connector
RESET
V
OUT
GATE
1422 F07
TIMER
ON
V
CC
V
SENSE
V
CC
1
2
3
4
5
6
7
8
9
10
because most people will rock the board back and forth to
get it seated properly.
A software-initiated power-down cycle can be started by
momentarily turning on transistor Q2, which will pull the
ON pin to ground. If the ON pin is held low for greater than
40祍, the GATE pin is pulled to ground. If the low pulse on
the ON pin is less than 15祍, a soft reset is generated.
Hot Swapping Two Supplies
With two external pass transistors, the LTC1422 can
switch two supplies. In some cases, it is necessary to bring
up the dominant supply first during power-up and ramp it
down last during the power-down phase. The circuit in
Figure 10 shows how to program two different delays for
the pass transistors. The 5V supply is powered up first. R1
Figure 7. Current Fault Timing
SENSE
7
V
CC
8
GATE
LTC1422
6
C1
1422 F08
Q1
R1
R
F
C
F
R2
Figure 8. Extending the Short-Circuit Protection Delay
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1642CGN#TRPBF | IC CONTROLLER HOTSWAP ADJ 16SSOP |
| LTC1643AL-1CGN#PBF | IC CTRLR HOTSWAP PCI BUS 16SSOP |
| LTC1644CGN#TRPBF | IC CONTROLLER HOT SWAP 20-SSOP |
| LTC1645IS#TRPBF | IC CTRLR SEQ HOTSWAP DUAL 14SOIC |
| LTC1646IGN#TR | IC CNTRLR HOTSWAP PCIDUAL 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1422CN8#PBF | 功能描述:IC CONTROLLER HOT SWAP 8-DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC1422CS8 | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC1422CS8#PBF | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC1422CS8#TR | 功能描述:IC CONTROLLER HOTSWAP 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC1422CS8#TRPBF | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。