- 您現在的位置：買賣IC網 > PDF目錄385503 > LTC1326-2.5 (Linear Technology Corporation) Micropower Precision Triple Supply Monitors(微功耗,三路電源精密監視器(2.5V，3.3V和可調)) PDF資料下載
參數資料
| 型號： | LTC1326-2.5 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Micropower Precision Triple Supply Monitors(微功耗,三路電源精密監視器(2.5V，3.3V和可調)) |
| 中文描述： | 微精密的三路電源監視器（微功耗，三路電源精密監視器（2.5伏，3.3伏和可調）） |
| 文件頁數： | 8/16頁 |
| 文件大小： | 257K |
| 代理商： | LTC1326-2.5 |
8
LTC1326/LTC1326-2.5
The three internal precision voltage comparators have
response times that are typically 13
μ
s. This slow re-
sponse time helps prevent mistriggering due to tran-
sients on each of the V
CC
inputs. The part’s ability to
suppress transients can be improved by bypassing each
of the V
CC
inputs with a 0.1
μ
F capacitor to ground.
Push-Button Reset
The parts provide a push-button reset input pin. The PBR
input has an internal pull-up current source to V
CC3
. If the
PBR pin is not used it can be left floating.
When the PBR is pulled low for less than t
PB
(
≈
2 sec), a
narrow (100
μ
s typ) soft reset pulse is generated on the
SRST output pin after the button is released. The push-
button circuitry contains an internal debounce counter
which delays the output of the soft reset pulse by typically
20ms. This pin can be OR-tied to the RST pin and issue
what is called a “soft” reset. The SRST thereby resets the
microprocessor without interrupting the DRAM refresh
cycle. In this manner DRAM information remains undis-
turbed. Alternatively, SRST may be monitored by the
processor to initiate a software-controlled reset.
When the PBR pin is held low for longer than t
PB
(
≈
2 sec),
a standard reset is generated on the RST and RST pins.
Once the 2 second period has elapsed, a reset signal is
produced by the push-button logic, thereby clearing the
reset counter. Once the button is released, the reset
counter begins counting the reset period (200ms nomi-
nal). Consequently, the reset outputs remain asserted for
approximately 200ms after the button is released.
TW
U
W
APPLICATIU
Operation
The LTC1326/LTC1326-2.5 are micropower, high accu-
racy triple supply monitoring circuits. The parts have two
basic functions: generation of a reset when power sup-
plies are out of range, and generation of reset or a “soft”
reset when the PBR pin is pulled low.
W
U
U
Supply Monitoring
All three V
CC
inputs must be above predetermined
thresholds for 200ms before the reset output is released.
The parts will assert reset during power-up, power-down
and brownout conditions on any one or more of the V
CC
inputs.
On power-up, either the V
CC5
or V
CC3
pin on the LTC1326,
or the V
CC25
or V
CC3
pin on the LTC1326-2.5, can power
the drive circuits for the RST pin. This ensures that RST
will be low when V
CC5
, V
CC25
or V
CC3
reaches 1V. As long
as any one of the V
CC
inputs is below its predetermined
threshold, RST will stay a logic low. Once all of the V
CC
inputs rise above their thresholds, an internal timer is
started and RST is released after 200ms. The RST pin
outputs the inverted state of what is seen on RST pin.
RST is reasserted whenever any one of the V
CC
inputs
drops below its predetermined threshold and remains
asserted until 200ms after all of the V
CC
inputs are above
their thresholds.
On power-down, once any of the V
CC
inputs drop below
its threshold, RST is held at a logic low. A logic low of 0.4V
is guaranteed until V
CC3
and V
CC5
on the LTC1326 or V
CC3
and V
CC25
on the LTC1326-2.5 drop below 1V.
Push-Button Reset Function Timing
t < t
PB
t
PB
t
RST
t
DB
t
SRST
1326
/2.5
TD02
PBR
RST
SRST
t
RST
1326
/2.5
TD01
V
RTX
V
CCX
RST
V
CC
Monitor Timing
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1327 | Octal Bus Transceivers/Registers With 3-State Outputs 24-SOIC 0 to 70 |
| LTC1327CG | 3.3V Micropower EIA/TIA-562 Transceiver |
| LTC1327CN | 3.3V Micropower EIA/TIA-562 Transceiver |
| LTC1327CS | 3.3V Micropower EIA/TIA-562 Transceiver |
| LTC1337 | 5V Low Power RS232 3-Driver/5-Receiver Transceiver(5V,低功耗，3發5收RS-232收發器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1326CMS8 | 功能描述:IC PREC TRPL SUPPLY MONITR 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| LTC1326CMS8#PBF | 功能描述:IC PREC TRPL SUPPLY MONITR 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| LTC1326CMS8#TR | 功能描述:IC MONITOR TRPL SPPLY PREC 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| LTC1326CMS8#TRPBF | 功能描述:IC PREC TRPL SUPPLY MONITR 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| LTC1326CMS8-2.5 | 功能描述:IC PREC TRPL SUPPLY MONITR 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
發布緊急采購，3分鐘左右您將得到回復。