- 您現在的位置：買賣IC網 > PDF目錄385502 > LTC1153C (Linear Technology Corporation) Auto-Reset Electronic Circuit Breaker PDF資料下載
參數資料
| 型號： | LTC1153C |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Auto-Reset Electronic Circuit Breaker |
| 中文描述： | 自動復位電子斷路器 |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 342K |
| 代理商： | LTC1153C |
8
LTC1153
LTC1153 OPERATIOU
Controlled Gate Rise and Fall Times
When the input is switched ON and OFF, the gate is
charged by the internal charge pump and discharged in a
controlled manner. The charge and discharge rates have
been set to minimize RFI and EMI emissions in normal
operation. If a short-circuit or current overload condition
is encountered, the gate is discharged very quickly (typi-
cally a few microseconds) by a large N-channel transistor.
Status Output Driver
The status circuitry continuously monitors the input and
the gate charge control logic. The open-drain output is
driven low when the input is turned ON and the breaker is
latched off. The status circuitry is reset along with the input
latch when the auto-reset circuitry retries the breaker or
the input is cycled low.
Figure 1. Protecting Resistive Loads
Figure 2. Protecting Inductive Loads
Large inductive loads (>0.1mH) may require diodes con-
nected directly across the inductor to safely divert the
stored energy to ground. Many inductive loads have these
diodes included. If not, a diode of the proper current rating
MOSFET and Load Protection
The LTC1153 protects the power MOSFET switch by
removing drive from the gate as soon as an over-current
condition is detected and breaking the circuit to the load.
Resistive and inductive loads can be protected with no
external time delay in series with the drain sense pin. High
inrush current loads, however, require that the trip delay
time be set long enough to start the load but short enough
to ensure the safety of the MOSFET.
Resistive Loads
Loads that are primarily resistive should be protected with
as short a delay as possible to minimize the amount of time
that the MOSFET switch or the load is subjected to an
overload condition. The drain sense circuitry has a built-
in trip delay of approximately 10
μ
s to eliminate false
triggering by power supply or load transient conditions.
This delay is sufficient to “mask” short load current
transients and the starting of a small capacitor (<1
μ
F) in
parallel with the load. The drain sense pin can therefore be
connected directly to the drain current sense resistor as
shown in Figure 1.
Inductive Loads
Loads that are primarily inductive, such as relays, sole-
noids and stepper motor windings should be protected
with as short a delay as possible to minimize the amount
of time that the MOSFET is subjected to an overload
condition. The built-in 10
μ
s trip delay will ensure that the
breaker is not false-tripped by a supply or load transient.
No external delay components are required as shown in
Figure 2.
U
S
A
O
PPLICATI
U
U
IN
C
T
STATUS
GND
V
S
DS
G
SD
LTC1153
C
0.22
μ
F
+
100
μ
F
IRFZ24
15V
R
LOAD
12
12V
C
LOAD
≤
1
μ
F
0.036
LTC1153 F01
IN
C
T
STATUS
GND
V
S
DS
G
SD
LTC1153
C
0.22
μ
F
+
100
μ
F
IRFZ24
15V
12V, 1A
SOLENOID
12V
1N5400
0.036
LTC1153 F02
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1153CN8 | Octal Bus Transceivers With 3-State Outputs 20-SOIC 0 to 70 |
| LTC1153CS8 | Auto-Reset Electronic Circuit Breaker |
| LTC1159-3. 3 | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
| LTC1159-5 | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
| LTC1159IS | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1153CN8 | 功能描述:IC ELECTRNC CIRCUIT BREAKER 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC1153CN8#PBF | 功能描述:IC ELECTRNC CIRCUIT BREAKER 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC1153CS8 | 功能描述:IC ELECTR CIRCUIT BREAKER 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC1153CS8#PBF | 功能描述:IC ELECTR CIRCUIT BREAKER 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:熱電冷卻器 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.173"，4.40mm 寬）裸露焊盤 供應商設備封裝:28-TSSOP 裸露焊盤 包裝:管件 產品目錄頁面:1410 (CN2011-ZH PDF) |
| LTC1153CS8#TR | 功能描述:IC CIRCUIT BRKR ELEC AUTO 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
發布緊急采購，3分鐘左右您將得到回復。