- 您現在的位置：買賣IC網 > PDF目錄385502 > LTC1147IS8-5 (LINEAR TECHNOLOGY CORP) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | LTC1147IS8-5 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SO-8 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 225K |
| 代理商： | LTC1147IS8-5 |
11
LTC1147-3.3
LTC1147-5/LTC1147L
sn1147 1147fds
where L1, L2, etc., are the individual losses as a percent-
age of input power. (For high efficiency circuits only small
errors are incurred by expressing losses as a percentage
of output power.)
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of the
losses in LTC1147 circuits: 1) LTC1147 DC bias current,
2) MOSFET gate charge current, 3) I
2
R losses, and 4)
voltage drop of the Schottky diode.
1. The DC supply current is the current which flows into
V
IN
(Pin 1) less the gate charge current. For V
IN
= 10V
the LTC1147 series DC supply current is 160
μ
A for no
load, and increases proportionally with load up to a
constant 1.6mA after the LTC1147 series has entered
continuous mode. Because the DC bias current is
drawn from V
IN
, the resulting loss increases with
input voltage. For V
IN
= 10V the DC bias losses are
generally less than 1% for load currents over 30mA.
However, at very low load currents the DC bias current
accounts for nearly all of the loss.
2. MOSFET gate charge current results from switching
the gate capacitance of the power MOSFET. Each time
a MOSFET gate is switched from low to high to low
again, a packet of charge dQ moves from V
IN
to
ground. The resulting dQ/dt is a current out of V
IN
which is typically much larger than the DC supply
current. In continuous mode, I
GATECHG
= f(Q
P
). The
typical gate charge for a 0.135
P-channel power
MOSFET is 40nC. This results in I
GATECHG
= 4mA in
100kHz continuous operation for a 2% to 3% typical
midcurrent loss with V
IN
= 10V.
Note that the gate charge loss increases directly with
both input voltage and operating frequency. This is the
principal reason why the highest efficiency circuits
operate at moderate frequencies. Furthermore, it ar-
gues against using a larger MOSFET than necessary to
control I
2
R losses, since overkill can cost efficiency as
well as money!
3. I
2
R losses are easily predicted from the DC resis-
tances of the MOSFET, inductor and current shunt. In
continuous mode the average output current flows
through L and R
SENSE
, but is “chopped” between the
P-channel and Schottky diode. The MOSFET R
DS(ON)
multiplied by the P-channel duty cycle can be summed
with the resistances of L and R
SENSE
to obtain I
2
R
losses. For example, if R
DS(ON)
= 0.1
, R
L
= 0.15
,
and R
SENSE
= 0.05
, then the total
resistance is 0.3
at V
IN
≈
2V
OUT
. This results in losses ranging from 3%
to 10% as the output current increases from 0.5A to
2A. I
2
R losses cause the efficiency to roll off at high
output currents.
4. The Schottky diode is a major source of power loss at
high currents and gets worse at high input voltages.
The diode loss is calculated by multiplying the forward
voltage drop times the Schottky diode duty cycle
multiplied by the load current. For example, assuming
a duty cycle of 50% with a Schottky diode forward
voltage drop of 0.4V, the loss increases from 0.5% to
8% as the load current increases from 0.5A to 2A.
Figure 5 shows how the efficiency losses in a typical
LTC1147 series regulator end up being apportioned.
The gate charge loss is responsible for the majority of
the efficiency lost in the midcurrent region. If Burst
Mode
operation was not employed at low currents,
the gate charge loss alone would cause efficiency to
drop to unacceptable levels. With Burst Mode
opera-
tion, the DC supply current represents the lone (and
unavoidable) loss component which continues to
become a higher percentage as output current is
reduced. As expected, the I
2
R losses and Schottky
diode loss dominate at high load currents.
Figure 5. Efficiency Loss
OUTPUT CURRENT (A)
0.01
E
90
95
1
LTC1147 F05
85
80
0.03
0.1
0.3
3
100
GATE CHARGE
LTC1147 I
Q
I
2
R
SCHOTTKY
DIODE
APPLICATIU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1148HVIS-5 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1151CSW | Dual 【15V Zero-Drift Operational Amplifier |
| LTC1151 | Dual ±15V Zero-Drift Operational Amplifier(±15V，雙路，零漂移運算放大器) |
| LTC1153 | Auto-Reset Electronic Circuit Breaker |
| LTC1153C | Auto-Reset Electronic Circuit Breaker |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1147IS8-5#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1147IS8-5#TR | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1147IS8-5#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1147L | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Efficiency Step-Down Switching Regulator Controllers |
| LTC1147LCS8 | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
發布緊急采購，3分鐘左右您將得到回復。