- 您現在的位置：買賣IC網 > PDF目錄1933 > LTC1064CSW#TRPBF (Linear Technology)IC FILTR BUILDNG BLK QUAD 24SOIC PDF資料下載
參數資料
| 型號： | LTC1064CSW#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 18/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FILTR BUILDNG BLK QUAD 24SOIC |
| 標準包裝： | 1,000 |
| 濾波器類型： | 通用開關電容器 |
| 頻率 - 截止或中心： | 140kHz |
| 濾波器數： | 4 |
| 濾波器階數： | 8th |
| 電源電壓： | ±2.37 V ~ 8 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC |
| 包裝： | 帶卷 (TR) |
LTC1064
7
1064fb
ANALOG
GROUND
PLANE
NOTE: CONNECT ANALOG AND DIGITAL
GROUND PLANES AT A SINGLE POINT AT
THE BOARD EDGE
FOR BEST HIGH FREQUENCY RESPONSE
PLACE RESISTORS PARALLEL TO DOUBLE-
SIDED COPPER CLAD BOARD AND LAY FLAT
(4 RESISTORS SHOWN HERE TYPICAL)
LTC1064
0.1
F
CERAMIC
PIN 1 IDENT
1064 F02
5k
–7.5V
7.5V
0.1
F CERAMIC
(SINGLE POINT
GROUND)
CLOCK
VIN
1
2
3
4
5
6
7
8
9
10
11
12
DIGITAL
GROUND
PLANE
24
23
22
21
20
19
18
17
16
15
14
13
APPLICATIONS INFORMATION
WU
U
Figure 2. Example Ground Plane Breadboard Technique for LTC1064
ANALOG CONSIDERATIONS
Grounding and Bypassing
The LTC1064 should be used with separated analog and
digital ground planes and single point grounding
techniques.
Pin 6 (AGND) should be tied directly to the analog ground
plane.
Pin 7 (V +) should be bypassed to the ground plane with a
0.1
F ceramic capacitor with leads as short as possible.
Pin 19 (V –) should be bypassed with a 0.1
F ceramic
capacitor. For single supply applications, V – can be tied to
the analog ground plane.
For good noise performance, V + and V – must be free of
noise and ripple.
All analog inputs should be referenced directly to the
single point ground. The clock inputs should be shielded
from and/or routed away from the analog circuitry and a
separate digital ground plane used.
Figure 2 shows an example of an ideal ground plane
design for a 2-sided board. Of course this much ground
plane will not always be possible, but users should strive
to get as close to this as possible. Protoboards are not
recommended.
Buffering the Filter Output
When driving coaxial cables and 1
× scope probes, the
filter output should be buffered. This is important espe-
cially when high Qs are used to design a specific filter.
Inadequate buffering may cause errors in noise, distor-
tion, Q and gain measurements. When 10
× probes are
used, buffering is usually not required. An inverting buffer
is recommended especially when THD tests are per-
formed. As shown in Figure 3, the buffer should be
adequately bypassed to minimize clock feedthrough.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1065IN8#PBF | IC FILTR 5TH ORDR LOWPASS 8-DIP |
| LTC1066-1CSW#TRPBF | IC FILTR 8TH ORDR LOWPASS 18SOIC |
| LTC1067CGN#TRPBF | IC FILTR BLDNGBLK R-R DUAL16SSOP |
| LTC1068-25IG#TRPBF | IC FILTR BUILDNG BLK QUAD 28SSOP |
| LTC1069-1IN8#PBF | IC FILTR 8TH ORDER LOWPASS 8-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1064M | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Low Noise, Fast, Quad Universal Filter Building Block |
| LTC1064MJ | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Low Noise, Fast, Quad Universal Filter Building Block |
| LTC1065 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:DC Accurate, Clock-Tunable Linear Phase 5th Order Bessel Lowpass Filter |
| LTC1065_09 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:DC Accurate, Clock-Tunable Linear Phase 5th Order Bessel Lowpass Filter |
| LTC1065C | 制造商:LINER 制造商全稱:Linear Technology 功能描述:DC Accurate, Clock-Tunable Linear Phase 5th Order Bessel Lowpass Filter |
發布緊急采購，3分鐘左右您將得到回復。