- 您現在的位置：買賣IC網 > PDF目錄44985 > LT3652HVEDD#PBF (LINEAR TECHNOLOGY CORP) BATTERY CHARGE CONTROLLER, PDSO12 PDF資料下載
參數資料
| 型號： | LT3652HVEDD#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | BATTERY CHARGE CONTROLLER, PDSO12 |
| 封裝： | 3 X 3 MM, LEAD FREE, PLASTIC, DFN-12 |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 250K |
| 代理商： | LT3652HVEDD#PBF |
LT3652HV
18
3652hvf
APPLICATIONS INFORMATION
of approximately 100mV appears at the charger output,
due to cycling between termination and recharge events,
This cycling results in pulsing at the CHRG output. An
LED connected to this pin will exhibit a blinking pattern,
indicating to the user that a battery is not present. The
frequency of this blinking pattern is dependent on the
output capacitance.
C/10 Termination
The LT3652HV supports a low-current based termination
scheme, where a battery charge cycle terminates when the
current output from the charger falls to below one-tenth
of the maximum current, as programmed with RSENSE.
The C/10 threshold current corresponds to 10mV across
RSENSE. This termination mode is engaged by shorting
the TIMER pin to ground.
When C/10 termination is used, a LT3652HV charger will
source battery charge current as long as the average current
level remains above the C/10 threshold. As the full-charge
float voltage is achieved, the charge current falls until
the C/10 threshold is reached, at which time the charger
terminates and the LT3652HV enters standby mode. The
CHRG status pin follows the charger cycle, and is high
impedance when the charger is not actively charging.
When VBAT drops below 97.5% of the full-charged float
voltage, whether by battery loading or replacement of the
battery, the charger automatically re-engages and starts
charging.
There is no provision for bad battery detection if C/10
termination is used.
Timer Termination
The LT3652HV supports a timer based termination scheme,
in which a battery charge cycle is terminated after a specific
amount of time elapses. Timer termination is engaged
when a capacitor (CTIMER) is connected from the TIMER
pin to ground. The timer cycle EOC (TEOC) occurs based
on CTIMER following the relation:
CTIMER = TEOC 2.27 x 10–7
(Hours)
Timer EOC is typically set to 3 hours, which requires a
0.68μF capacitor.
The CHRG status pin continues to signal charging at a C/10
rate, regardless of what termination scheme is used. When
timer termination is used, the CHRG status pin is pulled
low during a charging cycle until the charger output current
falls below the C/10 threshold. The charger continues to
top-off the battery until timer EOC, when the LT3652HV
terminates the charging cycle and enters standby mode.
Termination at the end of the timer cycle only occurs if
the charging cycle was successful. A successful charge
cycle is when the battery is charged to within 2.5% of the
full-charge float voltage. If a charge cycle is not successful
at EOC, the timer cycle resets and charging continues for
another full timer cycle.
When VBAT drops below 97.5% of the full-charge float
voltage, whether by battery loading or replacement of the
battery, the charger automatically reengages and starts
charging.
Preconditioning and Bad Battery Fault
A LT3652HV has a precondition mode, where charge cur-
rent is limited to 15% of the programmed ICHG(MAX), as
set by RSENSE. The precondition current corresponds to
15mV across RSENSE.
Precondition mode is engaged while the voltage on the
VFB pin is below the precondition threshold (2.3V, or
0.7 VBAT(FLT)). Once the VFB voltage rises above the
precondition threshold, normal full-current charging can
commence. The LT3652HV incorporates 70mV of threshold
hysteresis to prevent mode glitching.
相關PDF資料 |
PDF描述 |
|---|---|
| LT3652HVEMSE#TRPBF | BATTERY CHARGE CONTROLLER, PDSO12 |
| LT3652HVEDD#TRPBF | BATTERY CHARGE CONTROLLER, PDSO12 |
| LT3663EMS8E-3.3#PBF | 2.5 A SWITCHING REGULATOR, 1100 kHz SWITCHING FREQ-MAX, PDSO8 |
| LT3663IMS8E-3.3#PBF | 2.5 A SWITCHING REGULATOR, 1100 kHz SWITCHING FREQ-MAX, PDSO8 |
| LT3663IMS8E#TRPBF | 2.5 A SWITCHING REGULATOR, 1650 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3652HVEDD-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Power Tracking 2A Battery Charger |
| LT3652HVEMSE#PBF | 功能描述:IC BATTERY CHARGER 2A 12-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LT3652HVEMSE#PBF | 制造商:Linear Technology 功能描述:BATTERY CHARGER IC LEAD ACID LI-ION L 制造商:Linear Technology 功能描述:IC, BATTERY CHARGER, LITHIUM, 2A, MSOP12 |
| LT3652HVEMSE#TRPBF | 功能描述:IC BATTERY CHARGER 2A 12-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LT3652HVEMSE-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Power Tracking 2A Battery Charger |
發布緊急采購，3分鐘左右您將得到回復。