- 您現在的位置：買賣IC網 > PDF目錄44985 > LT3645IUD#PBF (LINEAR TECHNOLOGY CORP) 1.25 A SWITCHING REGULATOR, 825 kHz SWITCHING FREQ-MAX, PQCC16 PDF資料下載
參數資料
| 型號： | LT3645IUD#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.25 A SWITCHING REGULATOR, 825 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封裝： | 3 X 3 MM, LEAD FREE, PLASTIC, MO-220WEED-2, QFN-16 |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 296K |
| 代理商： | LT3645IUD#PBF |
LT3645
18
3645f
APPLICATIONS INFORMATION
P1 has a nite on-resistance which will result in power
dissipation and some loss in efciency. For higher buck
output voltage applications, a smaller PFET may be used
since the gate drive will be higher.
PCB Layout
For proper operation and minimum EMI, care must be taken
during printed circuit board layout. Figure 13 shows the
recommended component placement with trace, ground
plane, and via locations.
Note that large, switched currents ow in the LT3645’s VIN
and SW pins, the catch diode (D1), and the input capacitor
(C1). The loop formed by these components should be as
small as possible and tied to system ground in only one
place. These components, along with the inductor and
output capacitor, should be placed on the same side of the
circuit board, and their connections should be made on
that layer. Place a local, unbroken ground system ground in
only one place. These components, along with the inductor
and output capacitor, should be placed on the same side
of the circuit board, and their connections should be made
on that layer. Place a local, unbroken ground plane below
these components, and tie this ground plane to system
ground at one location (ideally at the ground terminal of
the output capacitor C1). The SW and BOOST nodes should
be kept as small as possible. Finally, keep the FB nodes
small so that the ground pin and ground traces will shield
them from the SW and BOOST nodes. Include vias near
the exposed GND pad of the LT3645 to help remove heat
from the LT3645 to the ground plane.
High Temperature Considerations
The die temperature of the LT3645 must be lower than
the maximum rating of 125°C (150°C for H-grade). This
is generally not a concern unless the ambient tempera-
ture is above 85°C. For higher temperatures, extra care
should be taken in the layout of the circuit to ensure good
heat sinking at the LT3645. The maximum load current
should be derated as the ambient temperature approaches
125°C. The die temperature is calculated by multiplying the
LT3645 power dissipation by the thermal resistance from
junction to ambient. Power dissipation within the LT3645
can be estimated by calculating the total power loss from
an efciency measurement and subtracting the catch diode
loss. The resulting temperature rise at full load is nearly
independent of input voltage. Thermal resistance depends
upon the layout of the circuit board, but 68°C/W is typical
for the QFN (UD) package, and 40°C/W is typical for the
MSE package. Thermal shutdown will turn off the Buck
and LDO when the die temperature exceeds 160°C, but
it is not a warrant to allow operation at die temperatures
exceeding 125°C (150°C for H-grade).
Other Linear Technology Publications
Application Notes 19, 35, and 44 contain more detailed
descriptions and design information for step-down regu-
lators and other switching regulators. The LT1376 data
sheet has an extensive discussion of output ripple, loop
compensation, and stability testing. Design Note 318
shows how to generate a bipolar output supply using a
step-down regulator.
Figure 13.
3645 F13
C3
C2
D1
DA
L1
SW
C4
C1
C5
R1
R3
MAIN PCB
BOARD
POWER
R2
FB1
BOOST
FB2
R4
OUT1
VIN
VCC2
EN/UVLO
NPG EN2
OUT2
VIA TO LOCAL GROUND PLANE
OUTLINE OF LOCAL GROUND PLANE
+
相關PDF資料 |
PDF描述 |
|---|---|
| LT3645EUD#TRPBF | 1.25 A SWITCHING REGULATOR, 825 kHz SWITCHING FREQ-MAX, PQCC16 |
| LT3645EMSE#TRPBF | 1.25 A SWITCHING REGULATOR, 825 kHz SWITCHING FREQ-MAX, PDSO12 |
| LT3651IUHE-4.2#PBF | BATTERY CHARGE CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PQCC36 |
| LT3651IUHE-4.2#TRPBF | BATTERY CHARGE CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PQCC36 |
| LT3651IUHE-4.1#TRPBF | BATTERY CHARGE CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PQCC36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3650 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage High Current Controller for Battery Charging and Power Management |
| LT3650-4.1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage 2 Amp Monolithic Li-Ion Battery Charger |
| LT3650-4.2 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage 2 Amp Monolithic Li-Ion Battery Charger |
| LT3650EDD-4.1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage 2 Amp Monolithic Li-Ion Battery Charger |
| LT3650EDD-4.1#PBF | 功能描述:IC CHARGER LI-ION 2A 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
發布緊急采購，3分鐘左右您將得到回復。