- 您現在的位置：買賣IC網 > PDF目錄44985 > LT3640IFE#TRPBF (LINEAR TECHNOLOGY CORP) 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PDSO28 PDF資料下載
參數資料
| 型號： | LT3640IFE#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | 4.40 MM, LEAD FREE, PLASTIC, TSSOP-28 |
| 文件頁數： | 23/24頁 |
| 文件大?。?/td> | 506K |
| 代理商： | LT3640IFE#TRPBF |
LT3640
3640f
pin FuncTions
FB2(Pin1/Pin26):Thelowvoltageconverterregulatesthe
FB2 pin to 600mV. Connect the feedback resistor divider
tap to this pin to set output voltage.
PGOOD (Pin 2/Pin 27): Open-drain logic output that starts
to sink current when FB2 is in regulation.
EN/UVLO (Pin 3/Pin 28): Pull this pin below 0.3V to shut
down the LT3640. The 1.26V threshold can function as an
accurateundervoltagelockout,preventingtheLT3640from
operating until VIN voltage has reached the programmed
level.
SYNC (Pin 4/Pin 1): Driving the SYNC pin with an external
clock signal synchronizes both converters to the applied
frequency. The lowest external clock frequency should be
20% higher than the internal oscillator frequency.
SS1 (Pin 5/Pin 2): The SS1 pin sets the FB1 voltage ex-
ternally between 0V and 1.265V, providing soft-start and
tracking. Tie this pin 1.5V or higher to use the internal
1.265V reference. A capacitor to ground at this pin sets the
ramp time to regulated output voltage for the high voltage
converter. Use a resistor divider to track another supply.
FB1(Pin6/Pin3):Thehighvoltageconverterregulatesthe
FB1 pin to 1.265V. Connect the feedback resistor divider
tap to this pin to set output voltage.
RT (Pin 7/Pin 4): Oscillator Resistor Input. Connecting a
resistor to ground from this pin sets the internal oscillator
frequency.
RST2 (Pin 8/Pin 5): Open-drain logic output that remains
asserted for the period set by the CPOR pin capacitor after
FB2 goes above 550mV.
RST1 (Pin 9/Pin 6): Open-drain logic output that remains
asserted for the period set by the CPOR pin capacitor after
FB1 goes above 1.165V.
WDO (Pin 10/Pin 7): Open-drain logic output that remains
asserted for the period set by the CPOR pin capacitor if
WDE is enabled and WDI pin is not driven by an appropri-
ate signal.
CWDT (Pin 11/Pin 8): Connect a capacitor to ground at
this pin to set watchdog timer.
CPOR (Pin 12/Pin 9): Connect a capacitor to ground at this
pin to set the power-on reset timer and WDO output timer.
WDE (Pin 13/Pin 10): Watchdog Enable Pin.
WDI (Pin 14/Pin 11): The WDI pin receives watchdog
signals from a microprocessor.
GND (Pins 15, 16, 23, 26, Exposed Pad Pin 29/Pins 12,
13, 20, 23, Exposed Pad Pin 29): Ground. These pins
must be soldered to PCB ground.
NC (Pin 17/Pin 14): Not Connected. This pin can be con-
nected to ground.
DA (Pin 18/Pin 15): The DA pin is used to sense the catch
diode current for current limit and protection. Connect this
pin to catch diode anode.
SW1 (Pin 19/Pin 16): Output of the High Voltage Internal
Power Switch. Connect this pin to the inductor and catch
diode cathode.
SW (Pin 20/Pin 17): The SW pin is used to charge the
boost capacitor. Connect this pin to the boost capacitor.
BST (Pin 21/Pin 18): The BST pin is used to provide a drive
voltage, higher than VIN pin voltage, to the high voltage
channel internal power switch. Connect an external boost
diode to this pin.
VIN (Pin 22/Pin 19): The VIN pin supplies current to
the LT3640’s internal circuitry and to the high voltage
channel internal power switch. This pin must be locally
bypassed.
VIN2 (Pin 24/Pin 21): The VIN2 pin supplies current to the
internal power MOSFET of the low voltage converter and
to the LT3640’s internal circuitry when VIN2 is above 3V.
SW2 (Pin 25/Pin 22): Switch Node of the Low Voltage
Converter. Connect this pin to an inductor.
EN2 (Pin 27/Pin 24): Low Voltage Converter Enable Pin.
Pull this pin below 0.3V to shut down the low voltage
converter. Pull this pin above 1.5V to enable the low volt-
age converter.
SS2 (Pin 28/Pin 25): The SS2 pin sets the FB2 voltage
externally between 0V and 0.6V, providing soft-start and
tracking. Tie this pin 0.8V or higher to use the internal
0.6V reference. A capacitor to ground at this pin sets the
ramp time to regulated output voltage for the low voltage
converter. Use a resistor divider to track another supply.
(FE/QFN)
相關PDF資料 |
PDF描述 |
|---|---|
| LT3640IUFD#PBF | 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PQCC28 |
| LT3640EUFD#TRPBF | 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PQCC28 |
| LT3640IUFD#TRPBF | 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PQCC28 |
| LT3645IUD#TRPBF | 1.25 A SWITCHING REGULATOR, 825 kHz SWITCHING FREQ-MAX, PQCC16 |
| LT3645IUD#PBF | 1.25 A SWITCHING REGULATOR, 825 kHz SWITCHING FREQ-MAX, PQCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3640IUFD | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Monolithic Buck Regulator with Power-On Reset and Watchdog Timer |
| LT3640IUFD#PBF | 功能描述:IC REG BUCK FIX/ADJ DL 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT3640IUFD#TRPBF | 功能描述:IC REG BUCK FIX/ADJ DL 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT3640IUFDPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Monolithic Buck Regulator with Power-On Reset and Watchdog Timer |
| LT3640IUFDTRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Monolithic Buck Regulator with Power-On Reset and Watchdog Timer |
發布緊急采購，3分鐘左右您將得到回復。