參數資料
型號: LT3640EFE#TRPBF
廠商: LINEAR TECHNOLOGY CORP
元件分類: 穩壓器
英文描述: 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PDSO28
封裝: 4.40 MM, LEAD FREE, PLASTIC, TSSOP-28
文件頁數: 13/24頁
文件大?。?/td> 506K
代理商: LT3640EFE#TRPBF
LT3640
0
3640f
3640 F10
L2
L1
CIN2
CIN
CBST
COUT1
COUT2
Figure 9a shows the power-on reset timing. Having FB1
or FB2 high starts the CPOR oscillator. After tRST, the cor-
responding RST is released. When both RST1 and RST2
are released, the CWDT oscillator starts. Figure 9b shows
thewatchdogwaveformwiththeWDIperiodbetweentWDL
and tWDU.TheWDIfallingedgeresetstheCWDToscillator.
The CPOR oscillator is disabled and WDO remains high.
Figure 9c shows the watchdog waveform with the WDI
period longer than tWDU. WDO is asserted for a period of
tRST when the watchdog upper boundary, tWDU, expires.
PCB Layout
For proper operation and minimum EMI, care must be
taken during the printed circuit board (PCB) layout. Figure
10 shows the recommended component placement with
trace, ground plane and via locations. The input loop of
the high voltage channel, which is formed by the VIN
and SW1 pins, the external catch diode (D1), the input
capacitor (CIN) and the ground, should be as small as
possible. These external components should be placed
on the same side of the circuit board as the LT3640, and
their connections should be made on that layer. Place a
local, unbroken ground plane below these components.
The BST and SW nodes should be as small as possible.
The boost capacitor (CBST) should be as close to the BST
and SW pins as possible.
The input loop of the low voltage channel is formed by
the VIN2 pin, the input capacitor (CIN2) and the ground.
Place CIN2 close to the VIN2 and the GND pin to minimize
this loop. Place a local, unbroken ground plane below
this input loop.
Keep the FB1 and FB2 nodes small so that the ground
traces will shield them from the switching nodes. The
Exposed Pad on the bottom of the package must be sol-
dered to the ground so that the pad acts as a heat sink. To
keep thermal resistance low, extend the ground plane as
much as possible, and add thermal vias under and near
the LT3640 to additional ground planes within the circuit
board and on the bottom side.
Figure 10. Recommended PCB Layout, FE28 Package
applicaTions inForMaTion
相關PDF資料
PDF描述
LT3640IFE#TRPBF 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PDSO28
LT3640IUFD#PBF 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PQCC28
LT3640EUFD#TRPBF 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PQCC28
LT3640IUFD#TRPBF 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PQCC28
LT3645IUD#TRPBF 1.25 A SWITCHING REGULATOR, 825 kHz SWITCHING FREQ-MAX, PQCC16
相關代理商/技術參數
參數描述
LT3640EUFD 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Monolithic Buck Regulator with Power-On Reset and Watchdog Timer
LT3640EUFD#PBF 功能描述:IC REG BUCK FIX/ADJ DL 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓(降壓) 輸出類型:固定 輸出數:1 輸出電壓:1.2V,1.5V,1.8V,2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP,10-MSOP(0.118",3.00mm 寬)裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤
LT3640EUFD#TRPBF 功能描述:IC REG BUCK FIX/ADJ DL 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓(升壓) 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型,TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
LT3640EUFDPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Monolithic Buck Regulator with Power-On Reset and Watchdog Timer
LT3640EUFDTRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Monolithic Buck Regulator with Power-On Reset and Watchdog Timer