- 您現在的位置：買賣IC網 > PDF目錄44985 > LT3571EUD#TRPBF (LINEAR TECHNOLOGY CORP) 0.57 A SWITCHING REGULATOR, 2300 kHz SWITCHING FREQ-MAX, PQCC16 PDF資料下載
參數資料
| 型號： | LT3571EUD#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.57 A SWITCHING REGULATOR, 2300 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封裝： | 3 X 3 MM, 0.50 MM PITCH, LEAD FREE, PLASTIC, MO-220WEED-2, QFN-16 |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 215K |
| 代理商： | LT3571EUD#TRPBF |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
LT3571
10
3571fa
APPLICATIONS INFORMATION
Inductor Selection
The inductors used with the LT3571 should have a
saturation current rating of 0.4A, or greater. If the device
is used in an application where the input supply will be
hot-plugged, the saturation current rating should be equal
to, or greater than, the peak inrush current. For best loop
stability, the inductor value selected should provide a
ripple current of 80mA or more. For a given VIN and VOUT,
the inductor value to use in continuous conduction mode
(CCM) is estimated by the formula:
L = D VIN
80mA
where:
D =
VOUT +1– VIN
VOUT +1
and f is the switching frequency.
To achieve low output voltage ripple, a small value inductor
should be selected to force the LT3571 to operate in
discontinuous conduction mode (DCM). The inequality
is true when the LT3571 is operating in discontinuous
conduction mode.
L < D VIN
ILIMIT
where ILIMIT is the switch current limit. Operating in DCM
reduces the maximum load current and the conversion
efciency.
Capacitor Selection
Low ESR capacitors should be used at the output to
minimize the output voltage ripple. Use only X5R and X7R
types, because they retain their capacitance over wider
voltage and temperature ranges than other types. High
output voltages typically require less capacitance for loop
stability. Typically, use a 1μF capacitor for output voltage
less than 25V, and a 0.22μF capacitor for output voltage
beyond 25V. Place the output capacitor as close as possible
to the VOUT lead and to the GND of the IC.
Either ceramic or solid tantalum capacitors may be used
for the input decoupling capacitor, which should be placed
as close as possible to the LT3571. A 1μF capacitor is
sufcient for most applications.
Phase Lead Capacitor
A small value capacitor (i.e., 10pF to 22pF) can be added
in parallel with the resistor between the output and the FB
pin to reduce output perturbation due to a load step and
to improve transient response. This phase lead capacitor
introduces a pole-zero pair to the feedback that boosts the
phase margin near the crossover frequency. The APD is
very sensitive to a noisy bias supply. To lowpass lter noise
from the internal reference and error amplier, a 0.1μF
phase lead capacitor can be used. The corner frequency
of the noise lter is R1 CPL.
APD Current Monitor
The power supply switching noise associated with a
switching power supply can interfere with the photodiode
DC measurement. To suppress this noise, a 0.1μF capacitor
is recommended at the APD pin. An additional series
resistor is necessary to ensure enough high frequency
compensation at the APD pin over the full operating range
of the LT3571, as shown in Figure 1. An additional output
lowpass lter, a 10k resistor and a 10nF capacitor in
parallel at MON pin can further reduce the power supply
noise, and other wide band noise, which might limit the
measurement accuracy of low current levels.
For applications requiring fast current monitor response
time, an RC lowpass lter at the MONIN pin is used to
replace the 0.1μF capacitor at the APD pin, as illustrated
in Figure 3.
Figure 3. RC Filter at MONIN Pin
MONIN
CFILT
3571 F03
VOUT
LT3571
APD
C1
RSENSE
相關PDF資料 |
PDF描述 |
|---|---|
| LT3574EMS#PBF | 1.1 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3574IMS#TRPBF | 1.1 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3579EUFD#PBF | SWITCHING REGULATOR, PQCC20 |
| LT3579IUFD-1#TRPBF | SWITCHING REGULATOR, PQCC20 |
| LT3579IFE#PBF | SWITCHING REGULATOR, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3571IUD#PBF | 功能描述:IC REG BOOST ADJ 0.47A 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT3571IUD#PBF | 制造商:Linear Technology 功能描述:DC-DC CONVERTER CURRENT MODE 制造商:Linear Technology 功能描述:DC-DC CONVERTER, CURRENT MODE, 2MHZ, QFN |
| LT3571IUD#TRPBF | 功能描述:IC REG BOOST ADJ 0.47A 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT3572 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Full-Bridge Piezo Driver with 900mA Boost Converter |
| LT3572EUF#PBF | 功能描述:IC DRIVER PIEZO DUAL 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:步進電機驅動器，1-2 相，2 相 評估套件:- 輸出數:1 電流 - 輸出:800mA 電壓 - 負載:10 V ~ 28 V 電源電壓:4.75 V ~ 5.25 V 工作溫度:-20°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:28-SOP + 2 翼片裸露焊盤 供應商設備封裝:28-HSOPHC（15.2x7.9） 包裝:剪切帶 (CT) 其它名稱:869-1268-1 |
發布緊急采購，3分鐘左右您將得到回復。