- 您現在的位置：買賣IC網 > PDF目錄44985 > LT3571EUD#PBF (LINEAR TECHNOLOGY CORP) 0.57 A SWITCHING REGULATOR, 2300 kHz SWITCHING FREQ-MAX, PQCC16 PDF資料下載
參數資料
| 型號： | LT3571EUD#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.57 A SWITCHING REGULATOR, 2300 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封裝： | 3 X 3 MM, 0.50 MM PITCH, LEAD FREE, PLASTIC, MO-220WEED-2, QFN-16 |
| 文件頁數： | 16/16頁 |
| 文件大小： | 215K |
| 代理商： | LT3571EUD#PBF |
LT3571
9
3571fa
Switching Frequency
There are two methods to set the switching frequency of the
LT3571. Both methods require a resistor connected at the
RT pin. Do not leave the RT pin open. Also, do not load this
pin with a capacitor. A resistor must always be connected
for proper operation. One way to set the frequency is simply
connecting an external resistor between the RT pin and
GND. See Table 1 or the Oscillator Frequency vs RT graph
in the Typical Performance Characteristics for resistor
values and corresponding switching frequencies. The other
way is to make the LT3571 synchronize with an external
clock via the SYNC pin. For proper operation, a resistor
should be connected at the RT pin and able to generate
a switching frequency 20% lower than the external clock
when the external clock is absent.
Table 1. Switching Frequency vs RT
Switching Frequency (kHz)
RT (k)
250
56.2
500
26.1
1000
12.1
1500
6.81
2000
4.22
2500
2.67
Inrush Current
The LT3571 has a built-in Schottky diode for the boost
converter. When supply voltage is applied to the VINpin,the
voltage difference between VIN and VOUT generates inrush
current owing from input through the inductor and the
Schottky diode (D1 in the Block Diagram), to charge the
output capacitor. The selection of inductor and capacitor
value should ensure the peak of the inrush current to below
1A. In addition, the LT3571 turn-on should be delayed until
the inrush current is less than the maximum current limit.
The peak inrush current can be estimated as follows:
IP =
VIN – 0.9
L
C
–1
exp –
π
2 L
C
–1
where L is the inductance, and C is the output capacitance.
Table 2 gives inrush peak currents for some component
selections.
Table 2. Inrush Peak Current
VIN (V)
L (μH)
C (μF)
IP (A)
5
10
1
0.81
5
22
1
0.63
Setting Output Voltage
The LT3571 is equipped with both an internal 1V reference
and an auxiliary reference input (the CTRL pin). This
feature allows users to select between using the built-in
reference and supplying an external reference voltage.
The voltage at the CTRL pin can be adjusted while the
chip is operating, to alter the output voltage of LT3571
for purposes such as APD’s bias voltage adjustment. To
use the internal 1V reference, the CTRL pin should be held
higher than 1.2V, which can be done by tying it to VREF.
When the CTRL pin is between 0V and 1V, the LT3571 will
regulate the output such that the FB pin voltage is equal
to the CTRL pin voltage. To set the output voltage, select
the values of R1 and R2 (see Figure 2) according to the
following equation:
R1 = R2
VMONIN
V1
–1
where V1 = 1V if the internal reference is used, or V1 =
CTRL if CTRL is between 0V and 1V. R2 can be selected to
load the output to maintain a constant switching frequency
when the APD load is very low. Preventing entry into
pulse-skipping mode is an important consideration for
post ltering the regulator output.
Figure 2. Output Voltage Feedback Connection
APPLICATIONS INFORMATION
MONIN
CTRL
R1
3
15
14
3571 F02
FB
LT3571
R2
相關PDF資料 |
PDF描述 |
|---|---|
| LT3571EUD#TRPBF | 0.57 A SWITCHING REGULATOR, 2300 kHz SWITCHING FREQ-MAX, PQCC16 |
| LT3574EMS#PBF | 1.1 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3574IMS#TRPBF | 1.1 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3579EUFD#PBF | SWITCHING REGULATOR, PQCC20 |
| LT3579IUFD-1#TRPBF | SWITCHING REGULATOR, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3571IUD#PBF | 功能描述:IC REG BOOST ADJ 0.47A 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT3571IUD#PBF | 制造商:Linear Technology 功能描述:DC-DC CONVERTER CURRENT MODE 制造商:Linear Technology 功能描述:DC-DC CONVERTER, CURRENT MODE, 2MHZ, QFN |
| LT3571IUD#TRPBF | 功能描述:IC REG BOOST ADJ 0.47A 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT3572 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Full-Bridge Piezo Driver with 900mA Boost Converter |
| LT3572EUF#PBF | 功能描述:IC DRIVER PIEZO DUAL 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:步進電機驅動器，1-2 相，2 相 評估套件:- 輸出數:1 電流 - 輸出:800mA 電壓 - 負載:10 V ~ 28 V 電源電壓:4.75 V ~ 5.25 V 工作溫度:-20°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:28-SOP + 2 翼片裸露焊盤 供應商設備封裝:28-HSOPHC（15.2x7.9） 包裝:剪切帶 (CT) 其它名稱:869-1268-1 |
發布緊急采購，3分鐘左右您將得到回復。