- 您現在的位置：買賣IC網 > PDF目錄44985 > LT3570EFE#PBF (LINEAR TECHNOLOGY CORP) 3.1 A SWITCHING REGULATOR, 2750 kHz SWITCHING FREQ-MAX, PDSO20 PDF資料下載
參數資料
| 型號： | LT3570EFE#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 3.1 A SWITCHING REGULATOR, 2750 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | 4.40 MM, LEAD FREE, PLASTIC, TSSOP-20 |
| 文件頁數： | 3/20頁 |
| 文件大?。?/td> | 283K |
| 代理商： | LT3570EFE#PBF |
LT3570
11
3570fb
to 1.2A at DC2 = 0.8. The maximum output current is a
function of the chosen inductor value:
IOUT2(MAX) =ILIM2 –
ΔIL2
2
= 1.5 1– 0.25 DC2
()– Δ
IL2
2
Choosing an inductor value so that the ripple current is
small will allow a maximum output current near the switch
current limit.
One approach to choosing the inductor is to start with the
simple rule given above, look at the available inductors
and choose one to meet cost or space goals. Then use
these equations to check that the LT3570 will be able to
deliver the required output current. Note again that these
equations assume that the inductor current is continu-
ous. Discontinuous operation occurs when IOUT2 is less
than
ΔIL2/2.
Boost Inductor Selection
For most applications the inductor will fall in the range
of 2.2μH to 22μH. Lower values are chosen to reduce
physical size of the inductor. Higher values allow more
output current because they reduce peak current seen by
the power switch, which has a 1.5A current limit. Higher
values also reduce input ripple voltage and reduce core
loss. The following procedure is suggested as a way of
choosing a more optimum inductor.
Assume that the average inductor current for a boost
converter is equal to the load current times VOUT1/VIN1
and decide whether or not the inductor must withstand
continuous overload conditions. If average inductor cur-
rent at maximum load current is 0.5A, for instance, a 0.5A
inductor may not survive a continuous 1.5A overload
condition. Also be aware that boost converters are not
short-circuit protected, and that under short conditions,
inductor current is limited only by the available current
of the input supply.
Calculate peak inductor current at full load current to en-
sure that the inductor will not saturate. Peak current can
be signicantly higher than output current, especially with
smaller inductors and lighter loads, so don’t omit this step.
Powdered iron cores are forgiving because they saturate
softly, whereas ferrite cores saturate abruptly. Other
core materials fall somewhere in between. The following
formula assumes continuous mode operation but it errs
only slightly on the high side for discontinuous mode, so
it can be used for all conditions.
IPEAK1 =
IOUT1 VOUT1
VIN1
+
VIN1 VOUT1 –VIN1
()
2 f L VOUT1
Make sure that IPEAK1 is less than the switch current ILIM1.
ILIM1 is at least 1.5A at low duty cycles and decreases
linearly to 1.2A at DC1 = 0.8. The maximum switch current
limit can be calculated by the following formula:
ILIM1 = 1.5 (1 – 0.25 DC1)
where DC1 is the duty cycle and is dened as:
DC1
= 1–
VIN1
VOUT1
Remember also that inductance can drop signicantly with
DC current and manufacturing tolerance. Consideration
should also be given to the DC resistance of the inductor
as this contributes directly to the efciency losses in the
overall converter. Table 1 lists several inductor vendors
and types that are suitable.
Buck Output Capacitor Selection
For 5V and 3.3V outputs, a 10μF, 6.3V ceramic capacitor
(X5R or X7R) at the output results in very low output volt-
age ripple and good transient response. For lower voltages,
10μF is adequate for ripple requirements but increasing
COUT will improve transient performance. Other types and
values will also work; the following discusses tradeoffs in
output ripple and transient performance.
The output capacitor lters the inductor current to generate
an output with low voltage ripple. It also stores energy in
order to satisfy transient loads and stabilize the LT3570’s
control loop. Because the LT3570 operates at a high
frequency, minimal output capacitance is necessary. In
addition, the control loop operates well with or without
the presence of output capacitor series resistance (ESR).
Ceramic capacitors, which achieve very low output ripple
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| LT3570IUF#TRPBF | 3.1 A SWITCHING REGULATOR, 2750 kHz SWITCHING FREQ-MAX, PQCC24 |
| LT3570EUF#TRPBF | 3.1 A SWITCHING REGULATOR, 2750 kHz SWITCHING FREQ-MAX, PQCC24 |
| LT3570EUF#PBF | 3.1 A SWITCHING REGULATOR, 2750 kHz SWITCHING FREQ-MAX, PQCC24 |
| LT3571IUD#PBF | 0.57 A SWITCHING REGULATOR, 2300 kHz SWITCHING FREQ-MAX, PQCC16 |
| LT3571EUD#PBF | 0.57 A SWITCHING REGULATOR, 2300 kHz SWITCHING FREQ-MAX, PQCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3570EFE-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.5A Buck Converter, 1.5A Boost Converter and LDO Controller |
| LT3570EUF#PBF | 功能描述:IC REG TRPL BCK/BST/LINEAR 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LT3570EUF#TRPBF | 功能描述:IC REG TRPL BCK/BST/LINEAR 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LT3570EUF-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.5A Buck Converter, 1.5A Boost Converter and LDO Controller |
| LT3570EUF-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.5A Buck Converter, 1.5A Boost Converter and LDO Controller |
發布緊急采購，3分鐘左右您將得到回復。