- 您現在的位置：買賣IC網 > PDF目錄30767 > LT3512EMS#PBF (LINEAR TECHNOLOGY CORP) 0.8 A SWITCHING REGULATOR, 650 kHz SWITCHING FREQ-MAX, PDSO12 PDF資料下載
參數資料
| 型號： | LT3512EMS#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.8 A SWITCHING REGULATOR, 650 kHz SWITCHING FREQ-MAX, PDSO12 |
| 封裝： | LEAD FREE, PLASTIC, MSOP-16/12 |
| 文件頁數： | 3/26頁 |
| 文件大?。?/td> | 244K |
| 代理商： | LT3512EMS#PBF |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
LT3512
11
3512fa
APPLICATIONS INFORMATION
TRANSFORMER DESIGN CONSIDERATIONS
Successful application of the LT3512 relies on proper
transformer specification and design. Carefully consider
the following information in addition to the traditional
guidelines associated with high frequency isolated power
supply transformer design.
Linear Technology has worked with several leading mag-
netic component manufacturers to produce pre-designed
flyback transformers for use with the LT3512. Table 1
shows the details of these transformers.
Turns Ratio
Note that when using an RFB/RREF resistor ratio to set
output voltage, the user has relative freedom in selecting
a transformer turns ratio to suit a given application. In
contrast, the use of simple ratios of small integers, e.g.,
1:1, 2:1, 3:2, provides more freedom in setting total turns
and mutual inductance.
Typically, choose the transformer turns to maximize avail-
able output power. For low output voltages (3.3V or 5V), a
N:1 turns ratio can be used with multiple primary windings
relative to the secondary to maximize the transformer’s
current gain (and output power). However, remember that
the SW pin sees a voltage that is equal to the maximum
input supply voltage plus the output voltage multiplied by
the turns ratio. In addition, leakage inductance will cause
a voltage spike (VLEAKAGE) on top of this reflected voltage.
This total quantity needs to remain below the absolute
maximum rating of the SW pin to prevent breakdown of
the internal power switch. Together these conditions place
an upper limit on the turns ratio, N, for a given application.
Choose a turns ratio low enough to ensure:
N
<
150V – VIN(MAX) –VLEAKAGE
VOUT + VF
For larger N:1 values, choose a transformer with a larger
physical size to deliver additional current. In addition,
choose a large enough inductance value to ensure that
the off-time is long enough to measure the output voltage.
For lower output power levels, choose a 1:1 or 1:N
transformer for the absolute smallest transformer size. A
1:N transformer will minimize the magnetizing inductance
(and minimize size), but will also limit the available output
power. A higher 1:N turns ratio makes it possible to have
very high output voltages without exceeding the breakdown
voltage of the internal power switch.
The turns ratio is an important element in the isolated
feedback scheme. Make sure the transformer manufacturer
guarantees turns ratio accuracy within ±1%.
Saturation Current
The current in the transformer windings should not ex-
ceed its rated saturation current. Energy injected once the
core is saturated will not be transferred to the secondary
and will instead be dissipated in the core. Information on
saturation current should be provided by the transformer
manufacturers. Table 1 lists the saturation current of the
transformers designed for use with the LT3512.
Primary Inductance Requirements
The LT3512 obtains output voltage information from the
reflected output voltage on the switch pin. The conduction
of secondary winding current reflects the output voltage
on the primary. The sampling circuitry needs a minimum
of 400ns to settle and sample the reflected output voltage.
In order to ensure proper sampling, the secondary winding
needs to conduct current for a minimum of 400ns. The
following equation gives the minimum value for primary-
side magnetizing inductance:
L
PRI ≥
t
OFF(MIN) NPS VOUT + VF
()
I
PEAK(MIN)
tOFF(MIN) = 400ns
IPEAK(MIN) = 100mA
In addition to the primary inductance requirement for
sampling time, the LT3512 has internal circuit constraints
that prevent the switch from staying on for less than 100ns.
If the inductor current exceeds the desired current limit
相關PDF資料 |
PDF描述 |
|---|---|
| LT3512HMS#TRPBF | 0.8 A SWITCHING REGULATOR, 650 kHz SWITCHING FREQ-MAX, PDSO12 |
| LT3512MPMS#PBF | 0.8 A SWITCHING REGULATOR, 650 kHz SWITCHING FREQ-MAX, PDSO12 |
| LT3512EMS#TRPBF | 0.8 A SWITCHING REGULATOR, 650 kHz SWITCHING FREQ-MAX, PDSO12 |
| LT3575IFE#PBF | 4.2 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3575EFE#PBF | 4.2 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3512HMS#PBF | 功能描述:IC REG FLYBK ISO ADJ .42A 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT3512HMS#TRPBF | 功能描述:IC REG FLYBK ISO ADJ .42A 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT3512HMSPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Monolithic High Voltage Isolated Flyback Converter |
| LT3512IMS#PBF | 功能描述:IC REG FLYBK ISO ADJ .42A 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT3512IMS#TRPBF | 功能描述:IC REG FLYBK ISO ADJ .42A 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
發布緊急采購，3分鐘左右您將得到回復。