- 您現在的位置：買賣IC網 > PDF目錄385502 > LT1715IMS (LINEAR TECHNOLOGY CORP) 4ns, 150MHz Dual Comparator with Independent Input/Output Supplies PDF資料下載
參數資料
| 型號： | LT1715IMS |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | 4ns, 150MHz Dual Comparator with Independent Input/Output Supplies |
| 中文描述： | DUAL COMPARATOR, 3500 uV OFFSET-MAX, PDSO10 |
| 封裝： | PLASTIC, MSOP-10 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 239K |
| 代理商： | LT1715IMS |
11
LT1715
APPLICATIO
S I
N
FOR
ATIO
U
W
U
With this in mind, calculation of the resistor values needed
is a two-step process. First, calculate the value of R3 based
on the additional hysteresis desired, the output voltage
swing and the impedance of the primary bias string:
R3 = (R1
R2)(+V
S
– 0.6V)/(additional hysteresis)
Additional hysteresis is the desired overall hysteresis less
the internal 4mV hysteresis.
The second step is to recalculate R2 to set the same
average threshold as before. The average threshold before
was set at V
TH
= (V
REF
)(R1)/(R1 + R2). The new R2 is
calculated based on the average output voltage (+V
S
/2)
and the simplified circuit model in Figure 7. To assure that
the comparator’s noninverting input is, on average, the
same V
TH
as before:
R2
′
= (V
REF
– V
TH
)/(V
TH
/R1 + (V
TH
– V
S
/2)/R3)
For additional hysteresis of 10mV or less, it is not uncom-
mon for R2
′
to be the same as R2 within 1% resistor
tolerances.
This method will work for additional hysteresis of up to a
few hundred millivolts. Beyond that, the impedance of R3
is low enough to effect the bias string, and adjustment of
R1 may also be required. Note that the currents through the
R1/R2 bias string should be many times the input currents
of the LT1715. For 5% accuracy, the current must be at least
20 times the input current, more for higher accuracy.
Interfacing the LT1715 to ECL
The LT1715’s comparators can be used in high speed
applications where Emitter-Coupled Logic (ECL) is de-
ployed. To interface the output of the LT1715 to ECL logic
inputs, standard TTL/CMOS to ECL level translators such
as the 10H124, 10H424 and 100124 can be used. These
components come at a cost of a few nanoseconds addi-
tional delay as well as supply currents of 50mA or more,
and are only available in quads. A faster, simpler and lower
power translator can be constructed with resistors as
shown in Figure 8.
Figure 8a shows the standard TTL to Positive ECL (PECL)
resistive level translator. This translator cannot be used for
the LT1715, or with CMOS logic, because it depends on the
820
resistor to limit the output swing (V
OH
) of the all-NPN
TTL gate with its so-called totem-pole output. The LT1715
is fabricated in a complementary bipolar process and the
output stage has a PNP driver that pulls the output nearly
all the way to the supply rail, even when sourcing 10mA.
Figure 8b shows a three resistor level translator for inter-
facing the LT1715 to ECL running off the same supply rail.
No pull-down on the output of the LT1715 is needed, but
pull-down R3 limits the V
IH
seen by the PECL gate. This is
needed because ECL inputs have both a minimum and
maximum V
IH
specification for proper operation. Resistor
values are given for both ECL interface types; in both cases
it is assumed that the LT1715 operates from the same
supply rail.
Figure 8c shows the case of translating to PECL from an
LT1715 powered by a 3V supply rail. Again, resistor values
are given for both ECL interface types. This time four re-
sistors are needed, although with 10KH/E, R3 is not needed.
In that case, the circuit resembles the standard TTL trans-
lator of Figure 8a, but the function of the new resistor, R4,
is much different. R4 loads the LT1715 output when high
so that the current flowing through R1 doesn’t forward
bias the LT1715’s internal ESD clamp diode. Although this
diode can handle 20mA without damage, normal
Figure 7. Model for Additional Hysteresis Calculations
Figure 6. Additional External Hysteresis
–
+
1/2 LT1715
INPUT
1715 F06
R2
V
REF
R3
R1
–
+
1/2 LT1715
1715 F07
R2
′
V
REF
V
TH
R3
+V
S
2
V
AVERAGE
=
R1
相關PDF資料 |
PDF描述 |
|---|---|
| LT1761 | 100mA, Low Noise, LDO Micropower Regulators in SOT-23(可調輸出,100mA,低噪聲，低壓差穩壓器（SOT-23封裝）) |
| LT1761-1.8 | 100mA, Low Noise, LDO Micropower Regulators in SOT-23(1.8V輸出，100mA,低噪聲，低壓差穩壓器（SOT-23封裝）) |
| LT1761-2 | 100mA, Low Noise, LDO Micropower Regulators in SOT-23(2V輸出，100mA,低噪聲，低壓差穩壓器（SOT-23封裝）) |
| LT1761-2.5 | 100mA, Low Noise, LDO Micropower Regulators in SOT-23(2.5V輸出，100mA,低噪聲，低壓差穩壓器（SOT-23封裝）) |
| LT1761-3 | 100mA, Low Noise, LDO Micropower Regulators in SOT-23(3V輸出，100mA,低噪聲，低壓差穩壓器（SOT-23封裝）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1715IMS#PBF | 功能描述:IC COMPARATOR 150MHZ DUAL 10MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:UltraFast™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:通用 元件數:1 輸出類型:CMOS，推挽式，滿擺幅，TTL 電壓 - 電源，單路/雙路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 電壓 - 輸入偏移（最小值）:5mV @ 5.5V 電流 - 輸入偏壓（最小值）:1pA @ 5.5V 電流 - 輸出（標準）:- 電流 - 靜態（最大值）:24µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:450ns 磁滯:±3mV 工作溫度:-40°C ~ 85°C 封裝/外殼:6-WFBGA，CSPBGA 安裝類型:表面貼裝 包裝:管件 其它名稱:Q3554586 |
| LT1715IMS#PBF | 制造商:Linear Technology 功能描述:COMPARATOR DUAL 4NS MSOP-10 制造商:Linear Technology 功能描述:COMPARATOR, DUAL, 4NS, MSOP-10 |
| LT1715IMS#TR | 功能描述:IC COMPARATOR 150MHZ DUAL 10MSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 比較器 系列:UltraFast™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:通用 元件數:1 輸出類型:CMOS，推挽式，滿擺幅，TTL 電壓 - 電源，單路/雙路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 電壓 - 輸入偏移（最小值）:5mV @ 5.5V 電流 - 輸入偏壓（最小值）:1pA @ 5.5V 電流 - 輸出（標準）:- 電流 - 靜態（最大值）:24µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:450ns 磁滯:±3mV 工作溫度:-40°C ~ 85°C 封裝/外殼:6-WFBGA，CSPBGA 安裝類型:表面貼裝 包裝:管件 其它名稱:Q3554586 |
| LT1715IMS#TRPBF | 功能描述:IC COMPARATOR 150MHZ DUAL 10MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:UltraFast™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:通用 元件數:1 輸出類型:CMOS，推挽式，滿擺幅，TTL 電壓 - 電源，單路/雙路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 電壓 - 輸入偏移（最小值）:5mV @ 5.5V 電流 - 輸入偏壓（最小值）:1pA @ 5.5V 電流 - 輸出（標準）:- 電流 - 靜態（最大值）:24µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:450ns 磁滯:±3mV 工作溫度:-40°C ~ 85°C 封裝/外殼:6-WFBGA，CSPBGA 安裝類型:表面貼裝 包裝:管件 其它名稱:Q3554586 |
| LT1715IMSPBF | 制造商:Linear Technology 功能描述:Comparator Dual RRO +/-6V/12V MSOP10 |
發布緊急采購，3分鐘左右您將得到回復。