參數資料
| 型號： | LT1635CN8 |
| 廠商： | Linear Technology |
| 文件頁數： | 12/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP/REF BUILD BLK R-R 8DIP |
| 標準包裝： | 50 |
| 放大器類型： | 通用 |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 0.05 V/µs |
| 增益帶寬積： | 175kHz |
| 電流 - 輸入偏壓： | 2nA |
| 電壓 - 輸入偏移： | 300µV |
| 電流 - 電源： | 135µA |
| 電流 - 輸出 / 通道： | 40mA |
| 電壓 - 電源，單路/雙路(±)： | 1.2 V ~ 10 V，±0.6 V ~ 5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 8-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 8-PDIP |
| 包裝： | 管件 |
9
LT1635
The LT1635 is fully specified with V + = 5V, V – = 0V and
VCM = 2.5V. The op amp offset voltage is internally
trimmed to a minimum value at these supply voltages. A
unique feature of this device is that it operates from a
single 1.2V supply up to
±5V. A full set of specifications is
provided at
±5V supply voltages. The positive supply pin
of the LT1635 should be bypassed with a small capacitor
(about 0.1
F), as well as the negative supply pin when
using split supplies.
Op Amp
The LT1635 is fully specified for single supply operation,
i.e., when the negative supply is 0V. Input common mode
range of the op amp includes ground and the output
swings within a few millivolts of ground while sinking
current. The input stage of the op amp incorporates phase
reversal protection to prevent false outputs from occur-
ring when the input is below the negative supply. Protec-
tive resistors have been included in the input leads so that
current does not become excessive when the inputs are
forced below the negative supply.
The op amp also includes an offset nulling feature, this is
accomplished by connecting the BALANCE pin (Pin 5) to
a variable voltage derived from the reference output. The
offset adjust range is asymmetrical, typically – 2mV to
8mV. At room temperature the input offset voltage of the
LT1635 is within the null range, thus the offset voltage can
be adjusted to zero. Figure 1 shows the standard offset
adjustment.
should be taken to keep the output from saturating. For
example, a 1mV input signal will cause the amplifier to set
up in its linear region in the gain 100 configuration as
shown in Figure 2a. However, 1mV is not enough to make
the amplifier function properly in the voltage follower mode
(Figure 2b).
Output
The output voltage swing of the LT1635 is a function of
input overdrive as shown in the typical performance curves.
When monitoring voltages within 15mV of either rail, gain
Distortion
There are two main contributors of distortion in op amps:
distortion caused by nonlinear common mode rejection
and output crossover distortion as the output transitions
from sourcing to sinking current. The common mode
rejection ratio of the LT1635 is very good, typically 110dB.
Therefore, as long as the input operates in normal com-
mon mode range, there will be very little common mode
induced distortion. Crossover distortion will increase as
the output load resistance decreases. For the lowest dis-
tortion, the LT1635 should be operated with the output
always sourcing current.
Reference
The reference of the LT1635 consists of a 200mV precision
bandgap and a reference amplifier. As shown in the block
diagram, the 0.2V precision bandgap is referred to V – and
is internally connected to the noninverting input of the ref-
erence amplifier. This configuration offers great flexibility
in that the reference voltage can be amplified or the reference
amplifier can be used as a comparator. Unlike the op amp,
the output of the reference amplifier can only swing within
0.8V (typ) of the positive rail. To guarantee that the reference
amplifier does not saturate over the industrial temperature
range, the minimum operating supply should be 1.3V. The
reference amplifier can source 2mA of load current and can
sink 10
A over the industrial temperature range.
Figure 2. Gain 100 Amplifier and Voltage Follower
–
+
LT1635
OP AMP
5V
99R
(a)
(b)
1mV
100mV
R
–
+
5V
1mV
1635 F02
OUTPUT
SATURATED
≈2mV
LT1635
OP AMP
–
+
LT1635
R1
10k
5
V –
V +
1
8
VREF
6
4
2
3
1635 F01
Figure 1. Standard Offset Adjustment
APPLICATIO S I FOR ATIO
WU
UU
相關PDF資料 |
PDF描述 |
|---|---|
| RGH2012-2E-P-183-B | RES 18K OHM .1% 1/4W 0805 SMD |
| 7100.1116.13 | FUSE 1.25A 250V T-LAG 19MM PCB |
| LTC6800HMS8 | IC INSTRUMENT AMP R-R I/O 8MSOP |
| WSLT2512R0180FEB | RES .018 OHM 1W 1% 2512 SMD |
| 7100.1117.13 | FUSE 1.6A 250V T-LAG 19MM PCB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1635CN8#PBF | 功能描述:IC OPAMP/REF BUILD BLK R-R 8DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| LT1635CS8 | 功能描述:IC OPAMP/REF BUILD BLK R-R 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LT1635CS8#8PBF | 制造商:Linear Technology 功能描述: |
| LT1635CS8#PBF | 功能描述:IC OPAMP/REF BUILD BLK R-R 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| LT1635CS8#TR | 功能描述:IC OPAMP/REF R-R MICROPWR 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
發(fā)布緊急采購，3分鐘左右您將得到回復。