參數資料
型號: LT1006CN8
廠商: Linear Technology
文件頁數: 2/16頁
文件大?。?/td> 0K
描述: IC PREC OP-AMP 5V SINGLE 8-DIP
標準包裝: 50
放大器類型: 通用
電路數: 1
轉換速率: 1.2 V/µs
電流 - 輸入偏壓: 10nA
電壓 - 輸入偏移: 30µV
電流 - 電源: 360µA
電壓 - 電源,單路/雙路(±): 5 V ~ 30 V,±2.5 V ~ 15 V
工作溫度: 0°C ~ 70°C
安裝類型: 通孔
封裝/外殼: 8-DIP(0.300",7.62mm)
供應商設備封裝: 8-PDIP
包裝: 管件
10
LT1006
1006fa
In automated production testing the output is forced to
1.4V by the test loop; offset voltage is measured with a
common mode voltage of zero and the negative supply at
zero (Pin 4). Without the test loop, these exact conditions
cannot be achieved. The test circuit shown ensures that
the output will never saturate even with worst-case offset
voltages (– 250V over the – 55°C to 125°C range). The
effective common mode input is 0.3V with respect to the
negative supply. As indicated by the common mode rejec-
tion specifications the difference is only a few microvolts
between the two methods of offset voltage measurement.
Low Supply Operation
The minimum guaranteed supply voltage for proper
operation of the LT1006 is 2.7V. Typical supply current at
this voltage is 320A; therefore, power dissipation is only
860W.
Noise Testing
For application information on noise testing and
calculations, please see the LT1007 or LT1028 data sheet.
Supply Current Programming
Connecting an optional external resistor to Pin 8 changes
the biasing of the LT1006 in order to increase its speed or
to decrease its power consumption. If a higher slew rate is
required, connect the external resistor for Pin 8 to Pin 4
[see performance curves for Increasing Slew Rate
(RSET to V)]. For lower power consumption, inject a
current into Pin 8 (which is approximately 60mV above
V) as shown on the Reducing Power Dissipation plot.
This can be accomplished by connecting RSET to the
positive supply, or to save additional power, by obtaining
the injected current from a low voltage battery.
Comparator Applications
The single supply operation of the LT1006 and its ability to
swing close to ground while sinking current lends itself
to use as a precision comparator with TTL compatible
output.
Comparator Rise Response Time
to 10mV, 5mV, 2mV Overdrives
Comparator Fall Response Time
to 10mV, 5mV, 2mV Overdrives
Test Circuit for Offset Voltage and
Offset Drift with Temperature
+
V0
4.7V
– 0.3V
LT1006
50k*
*
**
RESISTORS MUST HAVE LOW
THERMOELECTRIC POTENTIAL.
THIS CIRCUIT IS ALSO USED AS
THE BURN-IN CONFIGURATION,
WITH SUPPLY VOLTAGES
INCREASED TO ± 20V
VO = 1000VOS
LT1006 TA04
100
50k*
0
VS = 5V, 0V
50s/DIV
1006 TA12a
0
2
4
OUTPUT (V)
INPUT (mV)
–100
0
VS = 5V, 0V
50s/DIV
1006 TA12b
0
2
4
OUTPUT (V)
INPUT (mV) –100
0
APPLICATIO S I FOR ATIO
WU
UU
相關PDF資料
PDF描述
P6SMB12AT3 TVS ZENER UNIDIR 600W 12V SMB
SA5232N/01,112 IC OPAMP MATCHED DUAL LV 8-DIP
P6SMB120AT3 TVS ZENER UNIDIR 600W 120V SMB
MMD23-0141D1 CONN RACK/PANEL 14POS 5A
LTC6256IKC#TRPBF-ES IC OPAMP DUAL 6.5MHZ 8-UTDFN
相關代理商/技術參數
參數描述
LT1006CN8#PBF 功能描述:IC PREC OP-AMP 5V SINGLE 8-DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源,單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤,CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT
LT1006CN8PBF 制造商:Linear Technology 功能描述:Single precision op amp,LT1006CN8 DIP8
LT1006D8 制造商:Micross Components, Inc. 功能描述:OP AMP, PRECISION, SINGLE SUPPLY - Bulk
LT1006MH 制造商:Linear Technology 功能描述:OP Amp Single GP 44V 8-Pin TO-5
LT1006MH/883 制造商:Linear Technology 功能描述:OP Amp Single GP 44V 8-Pin TO-5