- 您現在的位置：買賣IC網 > PDF目錄44968 > LSN-2.5/10-D12BJ (CD TECHNOLOGIES INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | LSN-2.5/10-D12BJ |
| 廠商： | CD TECHNOLOGIES INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | SIP-11/9 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 753K |
| 代理商： | LSN-2.5/10-D12BJ |
LSN-10A D12 Series
N O N - I S O L A T E D , 1 0 - 5 0 W S I P D C / D C C O N V E R T E R S
Thermal Considerations and Thermal Protection
The typical output-current thermal-derating curves shown below enable
designers to determine how much current they can reliably derive from each
model of the LSN D12 SIP's under known ambient-temperature and air-ow
conditions. Similarly, the curves indicate how much air ow is required to
reliably deliver a specic output current at known temperatures.
The highest temperatures in LSN D12 SIP's occur at their output inductor,
whose heat is generated primarily by I2R losses. The derating curves were
developed using thermocouples to monitor the inductor temperature and
Typical Performance Curves for LSN D12 SIP Series
89
87
85
83
81
79
77
75
LSN-1/10-D12
Efficiency vs. Line Voltage and Load Current
1
2
3
4
5
6
7
8
9
10
Load Current (Amps)
E
ff
ic
ie
n
cy
(%
)
VIN = 10.8V
VIN = 12V
VIN = 13.2V
–40
0
60
70
80
90
100
110
LSN-1/10-D12
Output Current vs. Ambient Temperature
(Vertical mount, air flow direction from pin 11 to pin 1)
Output
Current
(Amps)
Ambient Temperature (
°C)
12
10
8
6
4
2
0
Natural Convection
200 lfm
100 lfm
6
Output Reverse Conduction
Many DC/DC's using synchronous rectication suffer from Output Reverse
Conduction. If those devices have a voltage applied across their output before
a voltage is applied to their input (this typically occurs when another power
supply starts before them in a power-sequenced application), they will either
fail to start or self destruct. In both cases, the cause is the "freewheeling" or
"catch" FET biasing itself on and effectively becoming a short circuit.
LSN D12 SIP DC/DC converters are not damaged from Output Reverse
Conduction. They employ proprietary gate drive circuitry which makes them
immune to applied voltages during the startup sequence. If you are using
an external power source paralleled with the LSN, be aware that during the
start up phase, some low impedance condition or transient current may be
absorbed briey into the LSN output terminals before voltage regulation is
fully established.You should insure that paralleled external power sources are
not disrupted by this condition during LSN start up.
varying the load to keep that temperature below +110°C under the assorted
conditions of air ow and air temperature. Once the temperature exceeds
+115°C (approx.), the thermal protection will disable the converter. Automatic
restart occurs after the temperature has dropped below +110°C.
All but the last two DUT's were vertical-mount models, and the direction of air
ow was parallel to the unit in the direction from pin 11 to pin 1.
As you may deduce from the derating curves and observe in the efciency
curves on the following pages, LSN D12 SIP's maintain virtually constant
efciency from half to full load, and consequently deliver very impressive
temperature performance even if operating at full load.
Lastly, when LSN D12 SIP's are installed in system boards, they are obvi-
ously subject to numerous factors and tolerances not taken into account here.
If you are attempting to extract the most current out of these units under
demanding temperature conditions, we advise you to monitor the output-
inductor temperature to ensure it remains below +110°C at all times.
Thermal Performance for "H" Models
Enhanced thermal performance can be achieved when LSN D12 SIP's are
mounted horizontally ("H" models) and the output inductor (with its electrically
isolating, thermally conductive pad installed) is thermally coupled to a copper
plane/pad (at least 0.55 square inches in area) on the system board.Your
conditions may vary, however our tests indicate this conguration delivers a
16°C to 22°C improvement in ambient operating temperatures. See page 9
for thermal comparison of two horizontally mounted units.
相關PDF資料 |
PDF描述 |
|---|---|
| LSN-1.2/10-D12J | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSN-2/10-D12BH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSN-2/10-D12 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSN-3.3/10-D12 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSN-1.1/10-D12BH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LSN2510D5 | 制造商:Datel 功能描述: |
| LSN2A | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters |
| LSN2B | 功能描述:限位開關 LIMIT SWITCH RoHS:否 制造商:Honeywell 觸點形式:SPDT 執行器:Non-Contact 電流額定值:30 mA 電壓額定值 AC: 電壓額定值 DC:3.6 V 工作力:10 g IP 等級:IP 67 NEMA 額定值:1, 4, 12, 13 端接類型:4-Pin M12 Connector 安裝:SMD/SMT |
| LSN2-T | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:DOSA-SIP, 30A POL DC/DC Converters |
| LSN2-T/10-C | 制造商:CANDD 制造商全稱:C&D Technologies 功能描述:Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters |
發布緊急采購，3分鐘左右您將得到回復。