- 您現在的位置：買賣IC網 > PDF目錄44968 > LSM2-T/6-D12-C (CD TECHNOLOGIES INC) 1-OUTPUT 19.8 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | LSM2-T/6-D12-C |
| 廠商： | CD TECHNOLOGIES INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 19.8 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT PACKAGE-7 |
| 文件頁數： | 13/17頁 |
| 文件大小： | 1504K |
| 代理商： | LSM2-T/6-D12-C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁
MDC_LSM2 Series.B01 Page 5 of 17
Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000
www.murata-ps.com
LSM2 Series
Single Putput, Non-Isolated
Selectable-Output POL DC/DC Converters
Figure 3. Measuring Output Ripple/Noise (PARD)
C1
C1 = NA
C2 = 22F TANTALUM
LOAD 2-3 INCHES (51-76mm) FROM MODULE
C2
RLOAD
6
4
COPPER STRIP
3
COPPER STRIP
SCOPE
+OUTPUT
COMMON
+SENSE
Figure 2. Measuring Input Ripple Current
Start-Up Time
The VIN to VOUT Start-Up Time is the interval between the time at which a ramp-
ing input voltage crosses the lower limit of the specified input voltage range
and the fully loaded output voltage enters and remains within its specified
accuracy band. Actual measured times will vary with input source impedance,
external input capacitance, and the slew rate and final value of the input volt-
age as it appears to the converter.
The On/Off to VOUT Start-Up Time assumes the converter is turned off via the
On/Off Control with the nominal input voltage already applied to the converter.
The specification defines the interval between the time at which the converter
is turned on and the fully loaded output voltage enters and remains within its
specified accuracy band. See Typical Performance Curves.
Remote Sense
LSM2 Series offer an output sense function. The sense function enables
point-of-use regulation for overcoming moderate IR drops in conductors and/or
cabling. Since these are non-isolated devices whose inputs and outputs usually
share the same ground plane, sense is provided only for the +Output.
The remote sense line is part of the feedback control loop regulating
the DC/DC converter’s output. The sense line carries very little current and
consequently requires a minimal cross-sectional-area conductor. As such,
it is not a low-impedance point and must be treated with care in layout and
cabling. Sense lines should be run adjacent to signals (preferably ground), and
in cable and/or discrete-wiring applications, twisted-pair or similar techniques
should be used. To prevent high frequency voltage differences between VOUT
and Sense, we recommend installation of a 1000pF capacitor close to the
converter.
The sense function is capable of compensating for voltage drops between
the +Output and +Sense pins that do not exceed 10% of VOUT.
[VOUT(+) – Common] – [Sense(+) – Common]
≤ 10%VOUT
Power derating (output current limiting) is based upon maximum output cur-
rent and voltage at the converter’s output pins. Use of trim and sense functions
can cause the output voltage to increase, thereby increasing output power
beyond the LSM2's specified rating. Therefore:
(VOUT at pins) x (IOUT)
≤ rated output power
The internal 10.5
W resistor between +Sense and +Output (see Figure 1)
serves to protect the sense function by limiting the output current flowing
through the sense line if the main output is disconnected. It also prevents
output voltage runaway if the sense connection is disconnected.
Note: If the sense function is not used for remote regulation, +Sense must
be tied to +Output at the DC/DC converter pins.
Sense Input
Use the Sense input with caution. Many applications do not need the Sense
connection. Sense is intended to correct small output accuracy errors caused
by the resistive ohmic drop in output wiring as output current increases. This
output drop (the difference between Sense and VOUT when measured at the
converter) should not be allowed to exceed 0.5V. Consider using heavier wire if
this drop is excessive.
Sense is connected at the load and corrects for resistive errors only. Be
careful where it is connected. Any long, distributed wiring and/or significant
inductance introduced into the Sense control loop can adversely affect overall
system stability. If in doubt, test the application, and observe the DC/DC's output
transient response during step loads. There should be no appreciable ringing or
oscillation. You may also adjust the output trim slightly to compensate for voltage
loss in any external filter elements. Do not exceed maximum power ratings.
On/Off Control
The On/Off Control pin may be used for remote on/off operation. Positive logic
LSM2 Series DC/DC converters are designed so that they are enabled when
the control pin is left open (open collector) and disabled when the control pin
is pulled low (to less than +0.3V relative to Common). As shown in Figure 4, all
models have an internal pull-up current source to VIN (+Input).
Dynamic control of the on/off function is best accomplished with a me-
chanical relay or open-collector/open-drain drive circuit (optically isolated if
appropriate). The drive circuit should be able to sink appropriate current when
activated and withstand appropriate voltage when deactivated.
相關PDF資料 |
PDF描述 |
|---|---|
| LSM2-T/10-W3NG-C | 1-OUTPUT 33 W DC-DC REG PWR SUPPLY MODULE |
| LSM2-T/6-D12N-C | 1-OUTPUT 19.8 W DC-DC REG PWR SUPPLY MODULE |
| LSM2-T/16-W3-C | 1-OUTPUT 52.8 W DC-DC REG PWR SUPPLY MODULE |
| LSM2-T/16-D12N-C | 1-OUTPUT 52.8 W DC-DC REG PWR SUPPLY MODULE |
| LSM2-T/6-W3NG-C | 1-OUTPUT 19.8 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LSM2T6W3C | 制造商:MURATA 功能描述:Pb Free |
| LSM2U | 功能描述:限位開關 LIMIT SWITCH RoHS:否 制造商:Honeywell 觸點形式:SPDT 執行器:Non-Contact 電流額定值:30 mA 電壓額定值 AC: 電壓額定值 DC:3.6 V 工作力:10 g IP 等級:IP 67 NEMA 額定值:1, 4, 12, 13 端接類型:4-Pin M12 Connector 安裝:SMD/SMT |
| LSM-3.3/10-D12 | 功能描述:DC/DC轉換器 33W 12V to 3.3V 10A SMT Package RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| LSM-3.3/10-D12-C | 功能描述:DC/DC轉換器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| LSM-3.3/10-D12EB | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:10 Amp DC/DC Power Converter Evaluation Boards |
發布緊急采購，3分鐘左右您將得到回復。