- 您現在的位置：買賣IC網 > PDF目錄44966 > LSM-1/10-D12-C (MURATA POWER SOLUTIONS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | LSM-1/10-D12-C |
| 廠商： | MURATA POWER SOLUTIONS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, SMT-6 |
| 文件頁數： | 18/18頁 |
| 文件大?。?/td> | 1583K |
| 代理商： | LSM-1/10-D12-C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁
MDC_LSM 10A D12 Models.B01 Page 9 of 18
Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000
www.murata-ps.com
Single Output
LSM-10A D12 Models
Non-Isolated, 12Vin, 0.75-5Vout DC/DC Converters
If you measure the input voltage before start up with a Digital Voltmeter
(DVM), the voltage may appear to be adequate. Limited external capacitance
and/or too high a source impedance may cause a short downward spike at
power up, causing an instantaneous voltage drop. Use an oscilloscope not a
DVM to observe this spike. The converter’s soft-start controller is sensitive to
input voltage. What matters here is the actual voltage at the input terminals at
all times.
Symptoms of start-up difficulties may include failed started, output oscilla-
tion or brief start up then overcurrent shutdown. Since the input voltage is never
absolutely constant, the converter may start up some times and not others.
Solutions
To improve start up, review the conditions above. One of the better solutions is
to place a moderate size capacitor very close to the input terminals. You may
need two parallel capacitors. A larger electrolytic or tantalum cap supplies the
surge current and a smaller parallel low-ESR ceramic cap gives low AC imped-
ance. Too large an electrolytic capacitor may have higher internal impedance
(ESR) and/or lower the start up slew rate enough to upset the DC/DC’s control-
ler. Make sure the capacitors can tolerate reflected switching current pulses
from the converter.
The capacitors will not help if the input source has poor regulation. A
converter which starts successfully at 3.3 Volts will turn off if the input voltage
decays to below the input voltage theshold, regardless of external capacitance.
Increase the input start up voltage if possible to raise the downward voltage
spike. Also, make sure that the input voltage ramps up in a reasonably short
time (less than a few milliseconds). If possible, move the input source closer to
the converter to reduce ohmic losses in the input wiring. Remember that the
input current is carried both by the wiring and the ground plane return. Make
sure the ground plane uses adequate thickness copper. Run additional bus wire
if necessary.
Any added output capacitor should use just enough capacitance (and no
more) to reduce output noise at the load and to avoid marginal threshold noise
problems with external logic. An output cap will also “decouple” inductive reac-
tance in the load. Certain kinds of electronic loads include “constant current”
characteristics which destabilize the output with insufficient capacitance. If the
wiring to the eventual load is long, consider placing this decoupling cap at the
load. Use the Remote Sense input to avoid ohmic voltage drop errors.
An elegant solution to start up problems is to apply the input voltage with
the Remote On/Off control first in the off setting (for those converters with an
On/Off Control). After the specified start-up delay (usually under 20 mSec), turn
on the converter. The controller will have already been stabilized. The short
delay will not be noticed in most applications. Be aware of applications which
need “power management” (phased start up).
Finally, it is challenging to model some application circuits with absolute
fidelity. How low is the resistance of your ground plane? What is the inductance
(and distributed capacitance) of external wiring? Even a detailed mathematical
model may not get all aspects of your circuit. Therefore it is difficult to give cap
values which serve all applications. Some experimentation may be required.
Typical Performance Curves for LSM D12 SMT Series
相關PDF資料 |
PDF描述 |
|---|---|
| LSM-1.2/10-D12-C | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSM-T/10-D12 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSM-T/10-D12-C | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSM-1.8/10-D12-C | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSM-1.5/16-W3-C | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LSM115J | 功能描述:DIODE SCHOTTKY 1A 15V DO214BA RoHS:否 類別:分離式半導體產品 >> 單二極管/整流器 系列:- 標準包裝:100 系列:- 二極管類型:標準 電壓 - (Vr)（最大）:50V 電流 - 平均整流 (Io):6A 電壓 - 在 If 時為正向 (Vf)（最大）:1.4V @ 6A 速度:快速恢復 = 200mA（Io） 反向恢復時間(trr):300ns 電流 - 在 Vr 時反向漏電:15µA @ 50V 電容@ Vr, F:- 安裝類型:底座，接線柱安裝 封裝/外殼:DO-203AA，DO-4，接線柱 供應商設備封裝:DO-203AA 包裝:散裝 其它名稱:*1N3879 |
| LSM115JE3/TR13 | 功能描述:DIODE SCHOTTKY 1A 15V DO214BA RoHS:是 類別:分離式半導體產品 >> 單二極管/整流器 系列:- 標準包裝:100 系列:- 二極管類型:標準 電壓 - (Vr)（最大）:50V 電流 - 平均整流 (Io):6A 電壓 - 在 If 時為正向 (Vf)（最大）:1.4V @ 6A 速度:快速恢復 = 200mA（Io） 反向恢復時間(trr):300ns 電流 - 在 Vr 時反向漏電:15µA @ 50V 電容@ Vr, F:- 安裝類型:底座，接線柱安裝 封裝/外殼:DO-203AA，DO-4，接線柱 供應商設備封裝:DO-203AA 包裝:散裝 其它名稱:*1N3879 |
| LSM115JTR7 | 制造商:Microsemi Corporation 功能描述: |
| LSM-11D | 制造商:EATON MOELLER 功能描述:BASIC UNIT METAL 1EARLY BR IP66 |
| LSM-11S | 制造商:Eaton 功能描述:Bulk 制造商:EATON MOELLER 功能描述:BASIC UNIT METAL 1NO/1NC IP66 |
發布緊急采購，3分鐘左右您將得到回復。