- 您現在的位置：買賣IC網 > PDF目錄361045 > LPC662AMD (NATIONAL SEMICONDUCTOR CORP) Low Power CMOS Dual Operational Amplifier PDF資料下載
參數資料
| 型號： | LPC662AMD |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 運算放大器 |
| 英文描述： | Low Power CMOS Dual Operational Amplifier |
| 中文描述： | DUAL OP-AMP, 3500 uV OFFSET-MAX, 0.35 MHz BAND WIDTH, CDIP8 |
| 封裝： | CERDIP-8 |
| 文件頁數： | 8/16頁 |
| 文件大小： | 585K |
| 代理商： | LPC662AMD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
Application Hints
(Continued)
amps, due to the additional gain stage; however, when driv-
ing load resistance of 5 k
or less, the gain will be reduced
as indicated in the Electrical Characteristics. The op amp
can drive load resistance as low as 500
without instability.
COMPENSATING INPUT CAPACITANCE
Refer to the LMC660 or LMC662 datasheets to determine
whether or not a feedback capacitor will be necessary for
compensation and what the value of that capacitor would be.
CAPACITIVE LOAD TOLERANCE
Like many other op amps, the LPC662 may oscillate when
its applied load appears capacitive. The threshold of oscilla-
tion varies both with load and circuit gain. The configuration
most sensitive to oscillation is a unity-gain follower. See the
Typical Performance Characteristics.
The load capacitance interacts with the op amp’s output re-
sistance to create an additional pole. If this pole frequency is
sufficiently low, it will degrade the op amp’s phase margin so
that the amplifier is no longer stable at low gains. The addi-
tion of a small resistor (50
to 100
) in series with the op
amp’s output, and a capacitor (5 pF to 10 pF) from inverting
input to output pins, returns the phase margin to a safe value
without interfering with lower-frequency circuit operation.
Thus, larger values of capacitance can be tolerated without
oscillation. Note that in all cases, the output will ring heavily
when the load capacitance is near the threshold for
oscillation.
Capacitive load driving capability is enhanced by using a
pull up resistor to V
+
Figure 3 Typically a pull up resistor
conducting 50 μA or more will significantly improve capaci-
tive load responses. The value of the pull up resistor must be
determined based on the current sinking capability of the
amplifier with respect to the desired output swing. Open loop
gain of the amplifier can also be affected by the pull up resis-
tor (see Electrical Characteristics).
PRINTED-CIRCUIT-BOARD LAYOUT
FOR HIGH-IMPEDANCE WORK
It is generally recognized that any circuit which must operate
with less than 1000 pA of leakage current requires special
layout of the PC board. When one wishes to take advantage
of the ultra-low bias current of the LPC662, typically less
than 0.04 pA, it is essential to have an excellent layout. For-
tunately, the techniques for obtaining low leakages are quite
simple. First, the user must not ignore the surface leakage of
the PC board, even though it may sometimes appear accept-
ably low, because under conditions of high humidity or dust
or contamination, the surface leakage will be appreciable.
To minimize the effect of any surface leakage, lay out a ring
of foil completely surrounding the LPC662’s inputs and the
terminals of capacitors, diodes, conductors, resistors, relay
terminals, etc. connected to the op-amp’s inputs. See Figure
4 To have a significant effect, guard rings should be placed
on both the top and bottom of the PC board. This PC foil
must then be connected to a voltage which is at the same
voltage as the amplifier inputs, since no leakage current can
flow between two points at the same potential. For example,
a PC board trace-to-pad resistance of 10
ohms, which is
normally considered a very large resistance, could leak 5 pA
if the trace were a 5V bus adjacent to the pad of an input.
This would cause a 100 times degradation from the
LPC662’s actual performance. However, if a guard ring is
held within 5 mV of the inputs, then even a resistance of
10
11
ohms would cause only 0.05 pA of leakage current, or
perhaps a minor (2:1) degradation of the amplifier’s perfor-
mance. See Figure 5a Figure 5b Figure 5c for typical con-
nections of guard rings for standard op-amp configurations.
If both inputs are active and at high impedance, the guard
can be tied to ground and still provide some protection; see
Figure 5d
DS010548-7
FIGURE 2. Rx, Cx Improve Capacitive Load Tolerance
DS010548-26
FIGURE 3. Compensating for Large
Capacitive Loads with A Pull Up Resistor
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LPC662IM | Low Power CMOS Dual Operational Amplifier |
| LPC662IN | Low Power CMOS Dual Operational Amplifier |
| LQA28A | 3V, 1W Boosted Boomer |
| LV8572A | LV8572A Low Voltage Real Time Clock (RTC) |
| LV8572AM | LV8572A Low Voltage Real Time Clock (RTC) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC662AMJ/883 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Low Power CMOS Dual Operational Amplifier |
| LPC662IM | 制造商:Texas Instruments 功能描述:OP Amp Dual GP R-R O/P 15.5V 8-Pin SOIC N Rail 制造商:Texas Instruments 功能描述:OP AMP, DUAL CMOS, SMD, SOIC8, 662 制造商:Texas Instruments 功能描述:OP AMP, DUAL CMOS, SMD, SOIC8, 662; Op Amp Type:Low Input Bias; No. of Amplifiers:2; Slew Rate:0.11V/s; Supply Voltage Range:5V to 15V; Amplifier Case Style:SOIC; No. of Pins:8; Bandwidth:350kHz; Operating Temperature Min:-40C; ;RoHS Compliant: Yes |
| LPC662IM | 制造商:Texas Instruments 功能描述:OP AMP DUAL CMOS SMD SOIC8 662 |
| LPC662IM/NOPB | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LPC662IMX | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。