參數資料
型號: LPC2470
廠商: NXP Semiconductors N.V.
英文描述: Flashless 16-bit/32-bit micro; Ethernet, CAN, LCD, USB 2.0 device/host/OTG, external memory interface
中文描述: 毛邊16-bit/32-bit微,以太網,CAN,液晶顯示器,USB 2.0設備/主機/ OTG功能,外部存儲器接口
文件頁數: 34/72頁
文件大?。?/td> 365K
代理商: LPC2470
LPC2470_0
NXP B.V. 2007. All rights reserved.
Preliminary data sheet
Rev. 00.01 — 5 October 2007
34 of 72
NXP Semiconductors
LPC2470
Fast communication chip
7.11 USB interface
The Universal Serial Bus (USB) is a 4-wire bus that supports communication between a
host and one or more (up to 127) peripherals. The Host Controller allocates the USB
bandwidth to attached devices through a token-based protocol. The bus supports hot
plugging and dynamic configuration of the devices. All transactions are initiated by the
host controller.
The LPC2470 USB interface includes a Device, Host, and OTG Controller. Details on
typical USB interfacing solutions can be found in
Section 11.2 “Suggested USB interface
solutions” on page 60
7.11.1
USB device controller
The device controller enables 12 Mbit/s data exchange with a USB Host Controller. It
consists of a register interface, serial interface engine, endpoint buffer memory, and a
DMA controller. The serial interface engine decodes the USB data stream and writes data
to the appropriate endpoint buffer. The status of a completed USB transfer or error
condition is indicated via status registers. An interrupt is also generated if enabled. When
enabled, the DMA controller transfers data between the endpoint buffer and the USB
RAM.
7.11.1.1
Features
Fully compliant with
USB 2.0 specification (full speed)
.
Supports 32 physical (16 logical) endpoints with a 4 kB endpoint buffer RAM.
Supports Control, Bulk, Interrupt and Isochronous endpoints.
Scalable realization of endpoints at run time.
Endpoint Maximum packet size selection (up to USB maximum specification) by
software at run time.
Supports SoftConnect and GoodLink features.
While USB is in the Suspend mode, LPC2470 can enter one of the reduced power
modes and wake up on USB activity.
Supports DMA transfers with the DMA RAM of 16 kB on all non-control endpoints.
Allows dynamic switching between CPU-controlled and DMA modes.
Double buffer implementation for Bulk and Isochronous endpoints.
7.11.2
USB Host Controller
The Host Controller enables full- and low-speed data exchange with USB devices
attached to the bus. It consists of register interface, serial interface engine and DMA
controller. The register interface complies with the OHCI specification.
7.11.2.1
Features
OHCI compliant
Two downstream ports
Support for per-port power switching
相關PDF資料
PDF描述
LPD200P70 PACKAGED HIGH DYNAMIC RANGE PHEMT
LPD200 HIGH PERFORMANCE PHEMT
LPD200MX HIGH PERFORMANCE PHEMT
LPD200SOT343 DIODE DUAL 1600V 2X43A TO-247AD
LPQ110 110 Watts
相關代理商/技術參數
參數描述
LPC2470_11 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Flashless 16-bit/32-bit microcontroller; Ethernet, CAN, LCD, USB 2.0 device/host/OTG
LPC2470_1109 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Flashless 16-bit/32-bit microcontroller; Ethernet, CAN, LCD, USB 2.0 device/host/OTG, external memory interface
LPC2470FBD208 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Flashless 16-bit/32-bit micro; Ethernet, CAN, LCD, USB 2.0 device/host/OTG, external memory interface
LPC2470FBD208,551 功能描述:ARM微控制器 - MCU LCD CONT/ETHNET USB/HOST/OTG RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2470FET208 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Flashless 16-bit/32-bit micro; Ethernet, CAN, LCD, USB 2.0 device/host/OTG, external memory interface