參數資料
型號: LPC2210
廠商: NXP Semiconductors N.V.
英文描述: 16/32-bit ARM microcontroller with 10-bit ADC and external memory interface
中文描述: 與10位ADC和外部存儲器接口16/32位ARM微控制器
文件頁數: 19/39頁
文件大小: 181K
代理商: LPC2210
Philips Semiconductors
LPC2210
16/32-bit ARM microcontrollers with external memory interface
Preliminary data
Rev. 01 — 09 February 2004
19 of 39
9397 750 12872
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
6.9 External memory controller
The external Static Memory Controller is a module which provides an interface
between the system bus and external (off-chip) memory devices. It provides support
for up to four independently configurable memory banks (16 MBytes each with byte
lane enable control) simultaneously. Each memory banks is capable of supporting
SRAM, ROM, Flash EPROM, Burst ROM memory, or some external I/O devices.
Each memory bank may be 8, 16, or 32 bits wide.
6.10 General purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by
the GPIO registers. Pins may be dynamically configured as inputs or outputs.
Separate registers allow setting or clearing any number of outputs simultaneously.
The value of the output register may be read back, as well as the current state of the
port pins.
6.10.1
Features
Direction control of individual bits.
Separate control of output set and clear.
All I/O default to inputs after reset.
19:18
20
Reserved.
If bits 5:4 are not 10, controls the use of pin P2.29:28: 0 enables P2.29:28, 1 is
reserved
If bits 5:4 are not 10, controls the use of pin P2.30: 0 enables P2.30, 1 enables
AIN4.
If bits 5:4 are not 10, controls the use of pin P2.31: 0 enables P2.31, 1 enables
AIN5.
Controls whether P3.0/A0 is a port pin (0) or an address line (1).
-
0
21
1
22
1
23
1 if BOOT1:0=00
at RESET=0,
0 otherwise
BOOT1 during
Reset
000 if
BOOT1:0=11 at
Reset, 111
otherwise
24
Controls whether P3.1/A1 is a port pin (0) or an address line (1).
27:25
Controls the number of pins among P3.23/A23/XCLK and P3.22:2/A2.22:2 that
are address lines:
000 = None
100 = A11:2 are address lines.
001 = A3:2 are address
lines.
010 = A5:2 are address
lines.
011 = A7:2 are address
lines.
Reserved.
101 = A15:2 are address lines.
110 = A19:2 are address lines.
111 = A23:2 are address lines.
31:28
Table 8:
PINSEL2 bits
Pin function select register 2 (PINSEL2 - 0xE002C014)
…continued
Description
Reset value
相關PDF資料
PDF描述
LPC2290 16/32-bit ARM microcontrollers with CAN, 10-bit ADC and external memory interface
LPC2292 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface
LPC2294JBD144 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface
LPC2294 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface
LPC2470 Flashless 16-bit/32-bit micro; Ethernet, CAN, LCD, USB 2.0 device/host/OTG, external memory interface
相關代理商/技術參數
參數描述
LPC2210_08 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:16/32-bit ARM microcontrollers; flashless, with 10-bit ADC and external memory interface
LPC2210FBD144 制造商:NXP Semiconductors 功能描述:
LPC2210FBD144,551 功能描述:ARM微控制器 - MCU RLESS/16K RAM/10B ADC/EXT BUS RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2210FBD144/01 制造商:NXP Semiconductors 功能描述:Microcontroller,LPC2210FBD144/01 75 MHz
LPC2210FBD144/01,5 功能描述:ARM微控制器 - MCU ARM7 16KR/10BADC ROMLESS RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT