- 您現在的位置：買賣IC網 > PDF目錄385494 > LP3991TL-2.8 (NATIONAL SEMICONDUCTOR CORP) 300mA Linear Voltage Regulator for Digital Applications PDF資料下載
參數資料
| 型號： | LP3991TL-2.8 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 300mA Linear Voltage Regulator for Digital Applications |
| 中文描述： | FIXED POSITIVE LDO REGULATOR, PBGA4 |
| 封裝： | 0.963 X 1.446 MM, LEAD FREE, MICRO SMD-4 |
| 文件頁數： | 11/14頁 |
| 文件大小： | 266K |
| 代理商： | LP3991TL-2.8 |
1μF to 4.7μF range. Another important consideration is that
tantalum capacitors have higher ESR values than equivalent
size ceramics. This means that while it may be possible to find
a tantalum capacitor with an ESR value within the stable
range, it would have to be larger in capacitance (which means
bigger and more costly) than a ceramic capacitor with the
same ESR value. It should also be noted that the ESR of a
typical tantalum will increase about 2:1 as the temperature
goes from 25°C down to -40°C, so some guard band must be
allowed.
ENABLE CONTROL
The LP3991 features an active high Enable pin, V
, which
turns the device on when pulled high. When not enabled the
regulator output is off and the device typically consumes 2nA.
If the application does not require the Enable switching fea-
ture, the V
pin should be tied to V
IN
to keep the regulator
output permanently on.
To ensure proper operation, the signal source used to drive
the V
input must be able to swing above and below the
specified turn-on/off voltage thresholds listed in the Electrical
Characteristics section under V
IL
and V
IH
.
micro SMD MOUNTING
The micro SMD package requires specific mounting tech-
niques which are detailed in the National Semiconductor
Application Note (AN-1112). Referring to the section
Surface
Mount Technology (SMT) Assenbly Considerations
, it should
be noted that the pad style which must be used with the 4 pin
package is NSMD (non-solder mask defined) type.
For best results during assembly, alignment ordinals on the
PCB may be used to facilitate placement of the micro SMD
device.
micro SMD LIGHT SENSITIVITY
Exposing the micro SMD device to direct sunlight may cause
mis-operation of the device. Light sources such as halogen
lamps can affect the electrical performance if brought near to
the device.
The wavelengths which have most detrimental effect are reds
and infra-reds, which means that fluorescent lighting, used
inside most buildings will have little effect on performance.
20110036
FIGURE 2. LP3991 Used as a Post DC/DC regulator
POST-BUCK REGULATOr
Linear Post-Regulation can be an effective way to reduce rip-
ple and switching noise from DC/DC convertors while still
maintaining a reasonably high overall efficiency.
The LP3991 is particularly suitable for this role due to its low
input voltage requirements. In addition, there is often no need
for a separate input capacitor for the LP3991 as it can share
the output cap of the DC/DC convertor.
Care of PCB layouts involving switching regulators is
paramount. In particular, the ground paths for the LDO should
be routed separately from the switcher ground and star con-
nected close to the battery. Routing of the switch pin of the
DC/DC convertor must be kept short to minimize radiated
EMI. A low pass filter such as a ferrite bead or common mode
choke on the battery input leads can further reduce radiated
EMI.
Figure 2
shows a typical example using an LM3673, 350mA
DC/DC buck regulator with a nominal output of 1.8V and a
1.5V LP3991. The overall efficiency will be greater than 70%
over the full Li-Ion battery voltage range. Maximum efficiency
is achieved by minimizing the difference between V
and
V
of the LP3991. The LP3991-1.5 will remain in regulation
down to an input voltage of 1.65V, so, in this case, a 1.8V
buck with 5% tolerance is adequate for all conditions of tem-
perature and load.
11
www.national.com
L
相關PDF資料 |
PDF描述 |
|---|---|
| LP3991TLX-1.2 | 300mA Linear Voltage Regulator for Digital Applications |
| LP3991TLX-1.3 | 300mA Linear Voltage Regulator for Digital Applications |
| LP3991TLX-1.5 | 300mA Linear Voltage Regulator for Digital Applications |
| LP3996SD-1525 | Dual Linear Regulator with 300mA and 150mA Outputs and Power-On-Reset |
| LP3996 | Dual Linear Regulator with 300mA and 150mA Outputs and Power-On-Reset |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LP3991TL-3.0/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP3991TLX-0.8/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP3991TLX-1.2/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP3991TLX-1.3/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP3991TLX-1.5/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。