- 您現在的位置：買賣IC網 > PDF目錄44717 > LP3946ILD (NATIONAL SEMICONDUCTOR CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 PDF資料下載
參數資料
| 型號： | LP3946ILD |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| 文件頁數： | 14/15頁 |
| 文件大?。?/td> | 337K |
| 代理商： | LP3946ILD |
Application Notes
LP3945 CHARGER OPERATION
The LP3945 is a complete battery charger with I
2C interface.
Charge cycle is initiated with wall adaptor insertion. If the
wall adaptor voltage appearing on the CHG-IN pin meets
under-voltage (V
UVLO-TSHD), over-voltage (VOVLO-TSHD), and
the Adaptor OK signal is detected, then pre-conditioning
process begins (see Figure 1). In pre-qualification cycle, a
safe current level, less than 65 mA, is pumped into the
battery while the voltage across the battery terminals is
measured. Once this voltage exceeds 3.0V, the controller
will initiate constant current fast charge cycle. During this
cycle, the 5.6 hr safety timer is started and charge current is
increased to I
CHG. The default value for ICHG is set during
manufacturing to 500 mA but it is user programmable from
500 mA to 950 mA in 50 mA step. The programmed current
is determined by battery type and manufacturers’ recom-
mendation.
If safety timer times out during constant current cycle, charg-
ing will be terminated if StopModeEN pin is pulled high. If it
is pulled low, device will proceed to operate in maintenance
mode and have to be interrupted externally. This is not a
recommended mode of operation. Disabling the 5.6hr timer
can potentially expose the battery to prolong charge cycle
and damage the battery. If StopModeEN feature is used,
user must protect the battery from exposure to prolong
charge cycle.
As the battery is charged during constant current mode, the
voltage across pack terminal increases until it reaches 4.1V
(or 4.2V). As soon as pack terminal exceeds 4.1V (or 4.2V),
controller starts operating in constant voltage mode by ap-
plying regulated V
BATT voltage across the battery terminal.
During this cycle, charge current, I
CHG, continues to de-
crease with time and when it drops below 0.1C (by default),
the EOC signal is activated indicating successful completion
of the charge cycle. The "C" term in 0.1C is the programmed
I
CHG. For example, 0.1C of 700mA is 70mA, and 0.2C of
700mA is 140mA. EOC current can be programmed to 0.1C,
0.15C, or 0.2C. The default value is 0.1C. After completing
the full charge cycle, controller will start maintenance cycle
where battery pack voltage is monitored continuously. If
during the maintenance cycle, pack voltage drops below
3.9V, charge cycle will be initiated providing that the wall
adaptor is plugged in and is alive.
Ni-MH charge mode (LP3945 only), which is a constant
voltage mode charging, can be selected by setting the
“mode” bit to HIGH via the I
2C interface.
The LP3945 with I
2C programming allows maximum flexibil-
ity in selecting charge current, battery regulation voltage
(4.1V or 4.2V), EOC current and battery type (Li Ion or
Ni-MH). The LP3945 operates in default mode during power
up. See the “I
2C Interface” section for more detail.
LP3946 CHARGER OPERATION
The LP3946 is a simpler version of the LP3945. It does not
have any I
2C interface, thus the device operates on default
setting. The values in BOLD in Table 1 are the default
settings. Default settings can be set at the factory to custom-
er’s specifications. For other options, please contact a Na-
tional Semiconductor sales office.
The LP3946 charges only Li Ion type battery.
TABLE 1. LP3946 Performance Options
Battery Voltage
Regulation (V)
End of Charge Current
Threshold (mA)
Charge
Current (mA)
4.1
0.1C
500
4.2
0.15C
550
0.20C
600
650
700
750
800
850
900
950
20066510
FIGURE 1. Charger Power Up and Power Down Waveform
LP3945/LP3946
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LP3972SQXA413 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC40 |
| LP3972SQX-5810 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC40 |
| LP3972SQXA514 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC40 |
| LP3972SQ-5810 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC40 |
| LP3972SQXE514 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LP3946ILDX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Battery Charge Management System |
| LP3946LD | 制造商:Rochester Electronics LLC 功能描述:STANDALONE CC/CV LIION BATTERY - Bulk |
| LP3946LD/NOPB | 功能描述:IC MANAGEMENT BATT CHARGE 14-LLP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| LP3947 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:USB/AC Adaptor, Single Cell Li-Ion Battery Charger IC |
| LP3947ISD-09 | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。