- 您現在的位置：買賣IC網 > PDF目錄358906 > LP2956 (National Semiconductor Corporation) Dual Micropower Low-Dropout Voltage Regulators PDF資料下載
參數資料
| 型號： | LP2956 |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Dual Micropower Low-Dropout Voltage Regulators |
| 中文描述： | 雙路微功率低壓差穩壓器 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 501K |
| 代理商： | LP2956 |
Application Hints
(Continued)
ESR may increase by a factor of
20
or
30
as the temperature
is reduced from +25C to 30C). The value of these capaci-
tors may be increased without limit.
The main output requires less capacitance at lighter load
currents. This capacitor can be reduced to 0.68 μF for cur-
rents below 10 mA or 0.22 μF for currents below 1 mA.
Programming the main output for voltages below 5V requires
more output capacitance for stability. For the worst-case
condition of 1.23V output and 250 mA of load current, a 6.8
μF (or larger) capacitor should be used.
A 1 μF capacitor should be placed from the input pin to
ground if there is more than 10 inches of wire between the in-
put and the AC filter capacitor or if a battery input is used.
Stray capacitance to the Feedback terminal can cause insta-
bility. This problem is most likely to appear when using high
value external resistors to set the output voltage. Adding a
100 pF capacitor between the Output and Feedback pins
and increasing the output capacitance to 6.8 μF (or greater)
will cure the problem.
MINIMUM LOAD ON MAIN OUTPUT
When setting the main output voltage using an external re-
sistive divider, a minimum current of 10 μA is recommended
through the resistors to provide a minimum load.
It should be noted that a minimum load current is specified in
several of the electrical characteristic test conditions, so the
specified value must be used to obtain test limit correlation.
PROGRAMMING THE MAIN OUTPUT VOLTAGE
The main output may be pin-strapped for 5V operation using
its internal resistive divider by tying the Output and Sense
pins together and also tying the Feedback and 5V Tap pins
together.
Alternatively, it may be programmed for any voltage between
the 1.23V reference and the 29V maximum rating using an
external pair of resistors (see Figure 3 ). The complete equa-
tion for the output voltage is:
where V
is the 1.23V reference and I
is the Feedback
pin bias current (20 nA typical). The minimum recom-
mended load current of 1 μAsets an upper limit of 1.2 M
on
the value of R2 in cases where the regulator must work with
no load (see
MINIMUM LOAD
).
If I
is ignored in the calculation of the output voltage, it will
produce a small error in V
. Choosing R2 = 100 k
will reduce this error to 0.16% (typical) while increasing the
resistor program current to 12 μA. Since the typical quies-
cent current is 130 μA, this added current is negligible.
DROPOUT VOLTAGE
The dropout voltage of the regulator is defined as the mini-
mum input-to-output voltage differential required for the out-
put voltage to stay within 100 mV of the output voltage mea-
sured with a 1V differential. The dropout voltage is
independent of the programmed output voltage.
DROPOUT DETECTION COMPARATOR
This comparator produces a logic “LOW” whenever the main
output falls out of regulation by more than about 5%. This fig-
ure results from the comparator’s built-in offset of 60 mV di-
vided by the 1.23V reference (refer to block diagram). The
5% low trip level remains constant regardless of the pro-
grammed output voltage. An out-of-regulation condition can
result from low input voltage, current limiting, or thermal lim-
iting.
Figure 4 gives a timing diagram showing the relationship be-
tween the main output voltage, the ERROR output, and input
voltage as the input voltage is ramped up and down to a
regulator whose main output is programmed for 5V. The ER-
ROR signal becomes low at about 1.3V input. It goes high at
about 5V input, where the main output equals 4.75V. Since
the dropout voltage is load dependent, the
input
voltage trip
points will vary with load current. The
main output
voltage
trip point does not vary.
The comparator has an open-collector output which requires
an external pull-up resistor. This resistor may be connected
to the regulator main output or some other supply voltage.
Using the main output prevents an invalid “HIGH” on the
comparator output which occurs if it is pulled up to an exter-
nal voltage while the regulator input voltage is reduced be-
low 1.3V. In selecting a value for the pull-up resistor, note
that while the output can sink 400 μA, this current adds to
battery drain. Suggested values range from 100 k
to 1 M
.
The resistor is not required if the output is unused.
DS011339-11
*See Application Hints
*
*
Drive with high to shut down
FIGURE 3. Adjustable Regulator
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LP2960AIM-3.3 | Adjustable Micropower 0.5A Low-Dropout Regulators |
| LP2960IM-3.3 | Adjustable Micropower 0.5A Low-Dropout Regulators |
| LP2960IM-5.0 | Adjustable Micropower 0.5A Low-Dropout Regulators |
| LP2960IN-3.3 | Adjustable Micropower 0.5A Low-Dropout Regulators |
| LP2960IN-5.0 | Adjustable Micropower 0.5A Low-Dropout Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LP2956AIM | 制造商:Texas Instruments 功能描述: |
| LP2956AIM/NOPB | 功能描述:IC REG LDO ADJ .25A 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:4V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.28V @ 150mA 穩壓器數量:1 電流 - 輸出:150mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:5-VFBGA 供應商設備封裝:5-uSMD 包裝:Digi-Reel® 其它名稱:LP2985AIBP-4.0DKR |
| LP2956AIMX | 功能描述:IC REG LDO ADJ .25A 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:4V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.28V @ 150mA 穩壓器數量:1 電流 - 輸出:150mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:5-VFBGA 供應商設備封裝:5-uSMD 包裝:Digi-Reel® 其它名稱:LP2985AIBP-4.0DKR |
| LP2956AIMX/NOPB | 制造商:Texas Instruments 功能描述:LDO Regulator Pos 1.23V to 29V 0.25A/0.075A 16-Pin SOIC N T/R |
| LP2956AIN/NOPB | 功能描述:IC REG LDO ADJ .25A 16-DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:4V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.28V @ 150mA 穩壓器數量:1 電流 - 輸出:150mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:5-VFBGA 供應商設備封裝:5-uSMD 包裝:Digi-Reel® 其它名稱:LP2985AIBP-4.0DKR |
發布緊急采購，3分鐘左右您將得到回復。