- 您現在的位置：買賣IC網 > PDF目錄16323 > LMK04033BEVAL (National Semiconductor)BOARD EVAL FOR LMK04033BISQ PDF資料下載
參數資料
| 型號： | LMK04033BEVAL |
| 廠商： | National Semiconductor |
| 文件頁數： | 20/65頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR LMK04033BISQ |
| 標準包裝： | 1 |
| 系列： | PowerWise® |
| 主要目的： | 計時，時鐘調節器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | LMK04033 |
| 主要屬性： | 122.88 MHz VCXO |
| 次要屬性： | 集成式 PLL 和 VCO |
| 已供物品： | 板，線纜，文檔 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
tCES
tCS
D27
D26
D25
D24
tCH
tCWH
tCWL
D23
D0
A3
A2
A1
A0
MSB
LSB
DATAuWire
CLKuWire
LEuWire
tES
tEWH
SNOSAZ8J – SEPTEMBER 2008 – REVISED SEPTEMBER 2011
Fout
The buffered output of the internal VCO is available at the Fout pin. This is a single-ended output (sinusoid).
Each time the PLL2_N counter value is updated via the uWire interface, an internal algorithm is triggered that
optimizes the VCO performance.
Digital Lock Detect 1 Bypass
The VCO coarse tuning algorithm requires a stable OSCin clock (reference clock to PLL2) to frequency calibrate
the internal VCO correctly. In order to ensure a stable OSCin clock, the first PLL must achieve lock status. A
digital lock detect is used in PLL1 to monitor its lock status. After lock is achieved by PLL1, the coarse tuning
circuitry is enabled and frequency calibration for the internal VCO begins.
The (DLD_BYP) pin is provided to allow an external bypass cap to be connected to the digital lock detect 1. This
capacitor will eliminate potential glitches at initial startup of PLL1 due to unknown phase relationships between
the Ncntr1 and Rcntr1.
Bias
Proper bypassing of this pin by a 1 F capacitor connected to VCC is important for low noise performance.
General Programming Information
LMK040xx devices are programmed using several 32-bit registers. Each register consists of a 4-bit address field
and 28-bit data field. The address field is formed by bits 0 through 3 (LSBs) and the data field is formed by bits 4
through 31 (MSBs). The contents of each register are clocked in MSB first (bit 31), and the LSB (bit 0) last.
During programming, the LE signal should be held LOW. The serial data is clocked in on the rising edge of the
CLK signal. After the LSB (bit 0) is clocked in the LE signal should be toggled LOW-to-HIGH-to-LOW to latch the
contents into the register selected in the address field. Registers R0-R4, R7, and R8-R15 must be programmed
in order to achieve proper device operation. Figure 12 illustrates the serial data timing sequence.
Figure 12. uWire Timing Diagram
To achieve proper frequency calibration, the OSCin port must be driven with a valid signal before programming
Register 15. Changes to PLL2_R Counter or the OSCin port signal require Register 15 to be reloaded in order to
activate the frequency calibration process.
Recommended Programming Sequence
The recommended programming sequence involves programming R7 with the reset bit set to 1 (Reg. 7, bit 4) to
ensure the device is in a default state. If R7 is programmed again, the reset bit should be set to 0. Registers are
programmed in order with R15 being the last register programmed. An example programming sequence is
shown below:
Program R7 with the RESET bit = 1 (b4 = 1). This ensures that the device is configured with default settings.
When RESET = 1, all other R7 bits are ignored.
–
- If R7 is programmed again during the initial configuration of the device, the RESET bit should be cleared
(b4 = 0)
Program R0 through R4 as necessary to configure the clock outputs as desired. These registers configure
clock channel functions such as the channel multiplexer output selection, divide value, delay value, and
enable/disable bit.
Copyright 2008–2011, Texas Instruments Incorporated
27
相關PDF資料 |
PDF描述 |
|---|---|
| H3AWH-6418G | IDC CABLE - HSC64H/AE64G/HPL64H |
| M3WWK-1406R | IDC CABLE - MPL14K/MC14M/MPL14K |
| 3-1906012-2 | CA 2.0MM OFNR 50/125,LC SEC RED |
| GBB09DHLR | CONN EDGECARD 18POS .050 DIP SLD |
| M3KKK-1406R | IDC CABLE - MPK14K/MC14M/MPK14K |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMK04033BEVAL/NOPB | 功能描述:時鐘和定時器開發工具 LMK04033BISQ EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Modules 類型:Clock Conditioners 工具用于評估:LMK04100B 頻率:122.8 MHz 工作電源電壓:3.3 V |
| LMK04033BISQ | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Low-Noise Clock Jitter Cleaner with Cascaded PLLs |
| LMK04033BISQ/NOPB | 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| LMK04033BISQE | 制造商:Texas Instruments 功能描述:Clock Conditioner 48-Pin LLP EP T/R 制造商:Texas Instruments 功能描述:PRECISION CLOCK CONDITIONER, 48LLP |
| LMK04033BISQE/NOPB | 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。