參數資料
型號: LM74CIM-3
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 溫度/濕度傳感器
英文描述: IC PROCESSOR UART ONE CHANNEL 16 BYTE RX/TX FIFO
中文描述: DIGITAL TEMP SENSOR-SERIAL, 13BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT
封裝: PLASTIC, SOP-8
文件頁數: 8/15頁
文件大小: 293K
代理商: LM74CIM-3
Typical Performance Characteristics
Average Power-On Reset Voltage vs Temperature
Static Supply Current vs Temperature (SO-8)
10090923
10090921
Static Supply Current vs Temperature (micro SMD)
Temperature Error (SO-8)
10090925
10090922
1.0 Functional Description
The LM74 temperature sensor incorporates a band-gap type
temperature sensor and 12-bit plus sign
Σ
ADC (Delta-
Sigma Analog-to-Digital Converter). Compatibility of the
LM74’s three wire serial interface with SPI and MICROWIRE
allows simple communications with common microcontrol-
lers and processors. Shutdown mode can be used to opti-
mize current drain for different applications.AManufacture’s/
Device
ID
register
identifies
Semiconductor product.
the
LM74
as
National
1.1 POWER UP AND POWER DOWN
When the supply voltage is less than about 1.6V (typical),
the LM74 is considered powered down. The LM74 always
powers up in a known state. When the supply voltage rises
above 1.6V (typical), an internal Power-On Reset (POR)
occurs and the temperature register will then contain a value
of 1111 1111 0000 00XX, where XX indicates undefined
values. See Section 1.5.2 for a diagram of the Temperature
Regisiter contents after POR but before completion of the
first temperature conversion.
The LM74 power-up default condition is continuous conver-
sion mode. After completion of the first full temperature
conversion, the register will contain temperature measure-
ment data in bits D15 (the temperature data MSB) through
D3 (the temperature data LSB). Bit D2 will be fixed high; bits
D1 and D0 are undefined. See Section 1.5.3 for a diagram of
the Temperature Regisiter contents after the first complete
temperature conversion. Note that bit D2 represents a com-
plete conversion flag. During POR it is low and, after the first
temperature conversion is complete, it goes high. This bit
can be polled to indicate when the POR data in the Tem-
perature Register has been replaced with valid temperature
data.
After the first conversion, and any subsequent conversions,
the value in the temperature register does not change until
the completion of the next conversion, at which time the
temperature register is updated with the latest temperature
value.
1.2 SERIAL BUS INTERFACE
The LM74 operates as a slave and is compatible with SPI or
MICROWIRE bus specifications. Data is clocked out on the
falling edge of the serial clock (SC), while data is clocked in
on the rising edge of SC. A complete transmit/receive com-
L
www.national.com
8
相關PDF資料
PDF描述
LM75BIM-3 Digital Temperature Sensor and Thermal WATCHDOG? with Two-Wire Interface
LM75DM-33R2 2-Wire Serial Temperature Sensor and Monitor
LM77000 Power Operational Amplifiers
LM77000CP Power Operational Amplifiers
LM77CIMM-5 9-Bit Sign Digital Temperature Sensor and Thermal Window Comparator with Two-Wire Interface
相關代理商/技術參數
參數描述
LM74CIM-3 T&R 制造商:Texas Instruments 功能描述:Temp Sensor Digital Serial (3-Wire, SPI) 8-Pin SOIC T/R
LM74CIM-3/NOPB 功能描述:板上安裝溫度傳感器 Digital Temp Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM74CIM-3/NOPB 制造商:Texas Instruments 功能描述:IC TEMP SENSOR
LM74CIM-3/NOPB 制造商:Texas Instruments 功能描述:Temperature Sensor IC
LM74CIM-5 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor