- 您現在的位置：買賣IC網 > PDF目錄358871 > LM6264 (National Semiconductor Corporation) High Speed Operational Amplifier PDF資料下載
參數資料
| 型號： | LM6264 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | High Speed Operational Amplifier |
| 中文描述： | 高速運算放大器 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 427K |
| 代理商： | LM6264 |
Simplified Schematic
Applications Tips
The LM6364 has been compensated for gains of 5 or greater
(over specified ranges of temperature, power supply voltage,
and
load).
Since
this
compensation
emitter-degeneration resistors in the op amp’s input stage,
the open-loop gain was reduced as the stability increased.
Gain error due to reduced A
is most apparent at high
gains; thus, the uncompensated LM6365 is appropriate for
gains of 25 or more. If unity-gain operation is desired, the
LM6361 should be used. The LM6361, LM6364, and
LM6365 have the same high slew rate (typically 300 V/μs),
regardless of their compensation.
The LM6364 is unusually tolerant of capacitive loads. Most
op amps tend to oscillate when their load capacitance is
greater than about 200 pF (in low-gain circuits). However,
load capacitance on the LM6364 effectively increases its
compensation capacitance, thus slowing the op amp’s re-
sponse and reducing its bandwidth. The compensation is not
ideal, though, and ringing or oscillation may occur in
low-gain circuits with large capacitive loads. To overcompen-
sate the LM6364 for operation at gains less than 5, a series
resistor-capacitor network should be added between the in-
put pins (as shown in the Typical Applications, Noise Gain
Compensation) so that the high-frequency noise gain rises
to at least 5.
involved
adding
Power supply bypassing will improve the stability and tran-
sient response of the LM6364, and is recommended for ev-
ery design. 0.01 μF to 0.1 μF ceramic capacitors should be
used (from each supply “rail” to ground); if the device is far
away from its power supply source, an additional 2.2 μF to
10 μF (tantalum) may be required for extra noise reduction.
Keep all leads short to reduce stray capacitance and lead in-
ductance, and make sure ground paths are low-impedance,
especially where heavier currents will be flowing. Stray ca-
pacitance in the circuit layout can cause signal coupling be-
tween adjacent nodes, so that circuit gain unintentionally
varies with frequency.
Breadboarded circuits will work best if they are built using
generic PC boards with a good ground plane. If the op amps
are used with sockets, as opposed to being soldered into the
circuit, the additional input capacitance may degrade circuit
performance.
DS009153-3
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LM6264N | High Speed Operational Amplifier |
| LM629M-6 | Precision Motion Controller |
| LM629M-8 | Precision Motion Controller |
| LM629N-6 | Precision Motion Controller |
| LM629N-8 | Precision Motion Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM6264N | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Speed Operational Amplifier |
| LM6265 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LM6265N | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Speed Operational Amplifier |
| LM627ACJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
| LM627ACN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
發布緊急采購，3分鐘左右您將得到回復。