<dfn id="kzzlv"><pre id="kzzlv"></pre></dfn>
  • <dfn id="kzzlv"></dfn>
  • <var id="kzzlv"><input id="kzzlv"></input></var>
    <tfoot id="kzzlv"><tr id="kzzlv"><sup id="kzzlv"></sup></tr></tfoot>
  • 參數資料
    型號: LM6225
    文件頁數: 4/10頁
    文件大?。?/td> 285K
    代理商: LM6225
    AC Electrical Characteristics
    The following specifications apply for Supply Voltage =
    ±
    15V, V
    = 0, R
    100 k
    and R
    S
    = 50
    unless otherwise noted.
    Boldface
    limits apply for T
    A
    = T
    J
    = T
    MIN
    to T
    MAX
    ; all other limits T
    A
    = T
    J
    = 25C.
    Symbol
    Parameter
    Conditions
    Typ
    LM6121
    Limit
    (Note 5)
    550
    550
    LM6221
    Limit
    (Note 5)
    550
    550
    LM6321
    Limit
    (Note 5)
    550
    550
    Units
    SR
    1
    SR
    2
    Slew Rate 1
    Slew Rate 2
    V
    IN
    =
    ±
    11V, R
    L
    = 1 k
    V
    IN
    =
    ±
    11V, R
    L
    = 50
    (Note 7)
    V
    IN
    = 2 V
    PP
    , R
    L
    = 50
    V
    +
    = 5V (Note 6)
    V
    IN
    =
    ±
    100 mV
    PP
    , R
    L
    = 50
    C
    L
    10 pF
    R
    L
    = 50
    , C
    L
    10 pF
    V
    O
    = 100 mV
    PP
    R
    L
    = 50
    , C
    L
    10 pF
    V
    O
    = 100 mV
    PP
    R
    L
    = 50
    , C
    L
    10 pF
    V
    O
    = 100 mV
    PP
    1200
    800
    V/μs
    Min
    SR
    3
    Slew Rate 3
    50
    550
    550
    550
    BW
    3 dB Bandwidth
    50
    30
    30
    30
    MHz
    Min
    ns
    t
    r
    , t
    f
    Rise Time
    Fall Time
    Propagation
    Delay Time
    Overshoot
    7.0
    t
    pd
    4.0
    ns
    O
    S
    10
    %
    Note 1:
    Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating
    the device beyond its rated operating conditions.
    Note 2:
    During current limit or thermal limit, the input current will increase if the input to output differential voltage exceeds 8V. For input to output differential voltages
    in excess of 8V the input current should be limited to
    ±
    20 mA.
    Note 3:
    The LM6121 series buffers contain current limit and thermal shutdown to protect against fault conditions.
    Note 4:
    The thermal resistance
    θ
    of the device in the N package is measured when soldered directly to a printed circuit board, and the heat-sinking pins (pins 1,
    4, 5 and 8) are connected to 2 square inches of 2 oz. copper. When installed in a socket, the thermal resistance
    θ
    of the N package is 84C/W. The thermal re-
    sistance
    θ
    of the device in the M package is measured when soldered directly to a printed circuit board, and the heat-sinking pins (pins 1, 2, 6, 7, 8, 9, 13, 14) are
    connected to 1 square inch of 2 oz. copper.
    Note 5:
    Limits are guaranteed by testing or correlation.
    Note 6:
    The input is biased to 2.5V and V
    IN
    swings V
    pp
    about this value. The input swing is 2 V
    pp
    at all temperatures except for the A
    V
    3 test at 55C where it is
    reduced to 1.5 V
    pp
    .
    Note 7:
    Slew rate is measured with a
    ±
    11V input pulse and 50
    source impedance at 25C. Since voltage gain is typically 0.9 driving a 50
    load, the output swing
    will be approximately
    ±
    10V. Slew rate is calculated for transitions between
    ±
    5V levels on both rising and falling edges.Ahigh speed measurement is done to minimize
    device heating. For slew rate versus junction temperature see typical performance curves. The input pulse amplitude should be reduced to
    ±
    10V for measurements
    at temperature extremes. For accurate measurements, the input slew rate should be at least 1700 V/μs.
    Note 8:
    The test circuit consists of the human body model of 120 pF in series with 1500
    .
    Note 9:
    For specification limits over the full Military Temperature Range, see RETS6121X.
    Note 10:
    The maximum power dissipation is a function of T
    J(max)
    ,
    θ
    JA
    , and T
    A
    . The maximum allowable power dissipation at any ambient temperature is P
    D
    =
    (T
    J(max)
    –T
    A
    )/
    θ
    JA
    .
    Typical Performance Characteristics
    T
    J
    = 25C, unless otherwise specified
    Frequency Response
    DS009223-11
    Frequency Response
    DS009223-12
    Slew Rate vs Temperature
    DS009223-13
    www.national.com
    4
    相關PDF資料
    PDF描述
    LM6225H Analog Buffer/Voltage Follower
    LM6121 High Speed Buffer
    LM6261MX Voltage-Feedback Operational Amplifier
    LM6265
    LM6361MX Voltage-Feedback Operational Amplifier
    相關代理商/技術參數
    參數描述
    LM6225H 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog Buffer/Voltage Follower
    LM6225N 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Speed Buffer
    LM6261 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Speed Operational Amplifier
    LM6261M 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Speed Operational Amplifier
    LM6261MX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier