- 您現在的位置：買賣IC網 > PDF目錄385487 > LM4918LQ (NATIONAL SEMICONDUCTOR CORP) Stereo Audio Amp with AGC Control PDF資料下載
參數資料
| 型號： | LM4918LQ |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻控制 |
| 英文描述： | Stereo Audio Amp with AGC Control |
| 中文描述： | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, QCC32 |
| 封裝： | LLP-32 |
| 文件頁數： | 11/17頁 |
| 文件大小： | 646K |
| 代理商： | LM4918LQ |
Application Information
(Continued)
mize thermal design may compromise the LM4918’s perfor-
mance and activate unwanted, though necessary, thermal
shutdown protection.
The LM4918LD must have its DAP soldered to a copper pad
on the PCB. The DAP’s PCB copper pad is then, ideally,
connected to a large plane of continuous unbroken copper.
This plane forms a thermal mass, heat sink, and radiation
area. Place the heat sink area on either outside plane in the
case of a two-sided or multi-layer PCB. (The heat sink area
can also be placed on an inner layer of a multi-layer board.
The thermal resistance, however, will be higher.) Connect
the DAP copper pad to the inner layer or backside copper
heat sink area with 2 vias. The via diameter should be
0.012in - 0.013in with a 1.27mm pitch. Ensure efficient ther-
mal conductivity by plugging and tenting the vias with plating
and solder mask, respectively. Further detailed and specific
information concerning PCB layout, fabrication, and mount-
ing an LQ (LLP) package is available in National Semicon-
ductor’s AN1187.
POWER SUPPLY BYPASSING
As with any power amplifier, proper supply bypassing is
critical for low noise performance and high power supply
rejection. Applications that employ a 5V regulator typically
use a 10μF in parallel with a 0.1μF filter capacitors to stabi-
lize the regulator’s output, reduce noise on the supply line,
and improve the supply’s transient response. However, their
presence does not eliminate the need for a local 1.0μF
tantalum bypass capacitance connected between the
LM4918’s supply pins and ground. Keep the length of leads
and traces that connect capacitors between the LM4918’s
power supply pin and ground as short as possible. Connect-
ing a 2.2μF capacitor, C
B
, between the BYPASS pin and
ground improves the internal bias voltage’s stability and
improves the amplifier’s PSRR. The PSRR improvements
increase as the bypass pin capacitor value increases. Too
large, however, increases turn-on time and can compromise
the amplifier’s click and pop performance. The selection of
bypass capacitor values, especially C
, depends on desired
PSRR requirements, click and pop performance system
cost, and size constraints.
200913I8
FIGURE 2. REFERENCE DESIGN BOARD SCHEMATIC
L
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM4924 | 2 Cell Battery, 40mW Per Channel Output Capacitor-Less(OCL) Stereo Headphone Audio Amplifier |
| LM4924MM | 2 Cell Battery, 40mW Per Channel Output Capacitor-Less(OCL) Stereo Headphone Audio Amplifier |
| LM4924SD | 2 Cell Battery, 40mW Per Channel Output Capacitor-Less(OCL) Stereo Headphone Audio Amplifier |
| LM4929 | Stereo 40mW Low Noise Headphone Amplifier with OCL Output |
| LM4929MM | Stereo 40mW Low Noise Headphone Amplifier with OCL Output |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4918LQ/NOPB | 功能描述:IC AMP AUDIO PWR 1.1W STER 32LLP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4919 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:1.5V, Mono 85mW BTL Output, 14mW Stereo Headphone Audio Amplifier |
| LM4919A WAF | 制造商:Texas Instruments 功能描述: |
| LM4919MM | 制造商:Texas Instruments 功能描述:AMP STEREO H/P 1.5V 14MW SMD 4919 |
| LM4919MM/NOPB | 功能描述:IC AMP AUDIO MONO/STER AB 10MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。