- 您現在的位置：買賣IC網 > PDF目錄385485 > LM4801 (National Semiconductor Corporation) 1W Stereo Audio Amplifier Plus Adjustable LDO PDF資料下載
參數資料
| 型號： | LM4801 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 1W Stereo Audio Amplifier Plus Adjustable LDO |
| 中文描述： | 1W的立體聲音頻放大器以及可調節穩壓器 |
| 文件頁數： | 15/20頁 |
| 文件大小： | 725K |
| 代理商： | LM4801 |
Application Information
(Continued)
ages, based on the Dropout Voltage vs Supply Voltage in the
Typical Performance Characteristics
curves, must be
added to the result obtained by Equation (8). The result in
Equation (9).
(8)
V
DD
≥
(V
OUTPEAK
+ (V
OD
TOP
+ V
OD
BOT
))
(9)
The Output Power vs Supply Voltage graph for an 8
load
indicates a minimum supply voltage of 4.6V. This is easily
met by the commonly used 5V supply voltage. The additional
voltage creates the benefit of headroom, allowing the
LM4801 to produce peak output power in excess of 1W
without clipping or other audible distortion. The choice of
supply voltage must also not create a situation that violates
maximum power dissipation as explained above in the
Power Dissipation
section.
After satisfying the LM4801’s power dissipation require-
ments, the minimum differential gain is found using Equation
(10).
(10)
Thus, a minimum gain of 2.83 allows the LM4801’s to reach
full output swing and maintain low noise and THD+N perfor-
mance. For this example, let A
VD
= 3.
The amplifier’s overall gain is set using the input (R
) and
feedback (R
) resistors. With the desired input impedance
set at 20k
, the feedback resistor is found using Equation
(11).
R
f
/R
i
= A
VD
/2
(11)
The value of R
f
is 30k
.
The last step in this design example is setting the amplifier’s
3dB frequency bandwidth. To achieve the desired
±
0.25dB
pass band magnitude variation limit, the low frequency re-
sponse must extend to at least onefifth the lower bandwidth
limit and the high frequency response must extend to at least
five times the upper bandwidth limit. The gain variation for
both response limits is 0.17dB, well within the
±
0.25dB
desired limit. The results are an
f
L
= 100Hz/5 = 20Hz
(12)
and an
F
H
= 20kHzx5 = 100kHz
(13)
As mentioned in the
External Components
section, R
i
and C
create a highpass filter that sets the amplifier’s lower
bandpass frequency limit. Find the coupling capacitor’s
value using Equation (14).
(14)
the result is
1/(2
π
*20k
*20Hz) = 0.398μF
(15)
Use a 0.39μF capacitor, the closest standard value.
The product of the desired high frequency cutoff (100kHz in
this example) and the differential gain, A
VD
, determines the
upper passband response limit. With A
VD
= 3 and f
H
=
100kHz, the closed-loop gain bandwidth product (GBWP) is
300kHz. This is less than the LM4801’s 3.5MHz GBWP. With
this margin, the amplifier can be used in designs that require
more differential gain while avoiding performance-lrestricting
bandwidth limitations.
LDO General Information
Figure 2 shows the LM4801’s LDO functional block diagram.
A 1.25V bandgap reference, an error amplifier and a PMOS
pass transistor perform voltage regulation while being sup-
ported by shutdown, fault, and the usual Temperature and
current protection circuitry
The regulator’s topology is the classic type with negative
feedback from the output to one of the inputs of the error
amplifier. Feedback resistors R
and R
are either internal or
external to the IC, depending on whether it is the fixed
voltage version or the adjustable version. The negative feed-
back and high open loop gain of the error amplifier cause the
two inputs of the error amplifier to be virtually equal in
voltage. If the output voltage changes due to load changes,
the error amplifier provides the appropriate drive to the pass
transistor to maintain the error amplifier’s inputs as virtually
equal. In short, the error amplifier keeps the output voltage
constant in order to keep its inputs equal.
Output Voltage Setting
The output voltage is set according to the amount of nega-
tive feedback (Note that the pass transistor inverts the feed-
back signal). Figure 3 simplifies the LDO’s topology. This
type of regulator can be represented as an op amp config-
ured as non-inverting amplifier and a fixed DC Voltage
(V
) for its input signal. The special characteristic of this
op amp is its extra-large output transistor that only sources
current. In terms of its non-inverting configuration, the output
voltage equals V
REF
times the closed loop gain:
200736A0
FIGURE 2. LDO Functional Block Diagram
L
www.national.com
15
相關PDF資料 |
PDF描述 |
|---|---|
| LM4801MH | 1W Stereo Audio Amplifier Plus Adjustable LDO |
| LM4805 | 3V, 1W Boosted Boomer |
| LM4805LQ | 3V, 1W Boosted Boomer |
| LM4808 | Dual 105 mW Headphone Amplifier |
| LM4808M | Dual 105 mW Headphone Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4801MH | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:1W Stereo Audio Amplifier Plus Adjustable LDO |
| LM480261 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Medium Size Graphic Type LCD Module |
| LM4802B | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Audio Power Amplifier with Boost Converter to Drive Ceramic Speakers |
| LM4802BLQ | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4802BLQ/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。