- 您現在的位置：買賣IC網 > PDF目錄10378 > LM4674TLX/NOPB (National Semiconductor)IC AMP AUDIO PWR 2.5W D 16USMD PDF資料下載
參數資料
| 型號： | LM4674TLX/NOPB |
| 廠商： | National Semiconductor |
| 文件頁數： | 5/27頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO PWR 2.5W D 16USMD |
| 產品培訓模塊： | PowerWise® Products and Technology |
| 標準包裝： | 3,000 |
| 系列： | Boomer® |
| 類型： | D 類 |
| 輸出類型： | 2 通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 2.5W x 2 @ 4 歐姆 |
| 電源電壓： | 2.4 V ~ 5.5 V |
| 特點： | 消除爆音，差分輸入，PWM，短路保護，關機 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 16-uSMD |
| 封裝/外殼： | 16-WFBGA |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | LM4674TLX |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
SNAS344E – DECEMBER 2005 – REVISED APRIL 2013
AUDIO AMPLIFIER INPUT CAPACITOR SELECTION
Input capacitors may be required for some applications, or when the audio source is single-ended. Input
capacitors block the DC component of the audio signal, eliminating any conflict between the DC component of
the audio source and the bias voltage of the LM4674. The input capacitors create a high-pass filter with the input
resistance Ri. The -3dB point of the high pass filter is found using Equation (1) below.
f = 1 / 2
πRiCi
(1)
The values for Ri can be found in the EC table for each gain setting.
The input capacitors can also be used to remove low frequency content from the audio signal. Small speakers
cannot reproduce, and may even be damaged by low frequencies. High pass filtering the audio signal helps
protect the speakers. When the LM4674 is using a single-ended source, power supply noise on the ground is
seen as an input signal. Setting the high-pass filter point above the power supply noise frequencies, 217 Hz in a
GSM phone, for example, filters out the noise such that it is not amplified and heard on the output. Capacitors
with a tolerance of 10% or better are recommended for impedance matching and improved CMRR and PSRR.
AUDIO AMPLIFIER GAIN SETTING
The LM4674 features four internally configured gain settings. The device gain is selected through the two logic
inputs, G0 and G1. The gain settings are as shown in the following table.
LOGIC INPUT
GAIN
G1
G0
V/V
dB
0
2
6
0
1
4
12
1
0
8
18
1
16
24
PCB LAYOUT GUIDELINES
As output power increases, interconnect resistance (PCB traces and wires) between the amplifier, load and
power supply create a voltage drop. The voltage loss due to the traces between the LM4674 and the load results
in lower output power and decreased efficiency. Higher trace resistance between the supply and the LM4674 has
the same effect as a poorly regulated supply, increasing ripple on the supply line, and reducing peak output
power. The effects of residual trace resistance increases as output current increases due to higher output power,
decreased load impedance or both. To maintain the highest output voltage swing and corresponding peak output
power, the PCB traces that connect the output pins to the load and the supply pins to the power supply should
be as wide as possible to minimize trace resistance.
The use of power and ground planes will give the best THD+N performance. In addition to reducing trace
resistance, the use of power planes creates parasitic capacitors that help to filter the power supply line.
The inductive nature of the transducer load can also result in overshoot on one or both edges, clamped by the
parasitic diodes to GND and VDD in each case. From an EMI standpoint, this is an aggressive waveform that
can radiate or conduct to other components in the system and cause interference. In is essential to keep the
power and output traces short and well shielded if possible. Use of ground planes beads and micros-strip layout
techniques are all useful in preventing unwanted interference.
As the distance from the LM4674 and the speaker increases, the amount of EMI radiation increases due to the
output wires or traces acting as antennas become more efficient with length. Ferrite chip inductors places close
to the LM4674 outputs may be needed to reduce EMI radiation.
Copyright 2005–2013, Texas Instruments Incorporated
13
Product Folder Links: LM4674
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J43-MY-B1 | CONVERTER MOD DC/DC 24V 50W |
| 5380-4PG-3DC | CONN RCPT 4POS CABLE PIN |
| VI-J1Z-MY-B1 | CONVERTER MOD DC/DC 2V 20W |
| 5182-2PG-3DC | CONN RCPT 2POS CABLE PIN |
| VI-J1Z-MX-B1 | CONVERTER MOD DC/DC 2V 30W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4675 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Ultra-Low EMI, Filterless, 2.65W, Mono, Class D Audio Power Amplifier with Spread Spectrum |
| LM4675SD | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Ultra-Low EMI, Filterless, 2.65W, Mono, Class D Audio Power Amplifier with Spread Spectrum |
| LM4675SD/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4675SDBD | 功能描述:音頻 IC 開發工具 LM4675SD EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| LM4675SDBD/NOPB | 功能描述:BOARD EVAL FOR LM4675SD RoHS:是 類別:編程器，開發系統 >> 評估板 - 音頻放大器 系列:Boomer®, PowerWise® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
發布緊急采購，3分鐘左右您將得到回復。