- 您現在的位置：買賣IC網 > PDF目錄385485 > LM4031AI (National Semiconductor Corporation) Self-Calibrating 12-Bit Plus Sign Serial I/O A/D Converters with MUX and Sample/Hold PDF資料下載
參數資料
| 型號： | LM4031AI |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 串行ADC |
| 英文描述： | Self-Calibrating 12-Bit Plus Sign Serial I/O A/D Converters with MUX and Sample/Hold |
| 中文描述： | 自校準12位帶符號串行I /辦公自動化/ D轉換器MUX和采樣/保持 |
| 文件頁數： | 11/41頁 |
| 文件大?。?/td> | 1152K |
| 代理商： | LM4031AI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
Note 5:
The human body model is a 100 pF capacitor discharged through a 1.5 k
resistor into each pin.
Note 6:
See AN450 “Surface Mounting Methods and Their Effect on Product Reliability” or the section titled “Surface Mount” found in any post 1986 National
Semiconductor Linear Data Book for other methods of soldering surface mount devices.
Note 7:
Two on-chip diodes are tied to each analog input through a series resistor as shown below. Input voltage magnitude up to 5V above V
+ or 5V below GND
will not damage this device. However, errors in the A/D conversion can occur (if these diodes are forward biased by more than 50 mV) if the input voltage magnitude
of selected or unselected analog input go above V
A
+ or below GND by more than 50 mV. As an example, if V
A
+ is 4.5 V
DC
, full-scale input voltage must be
≤
4.55
V
DC
to ensure accurate conversions.
01135402
Note 8:
To guarantee accuracy, it is required that the V
A
+ and V
D
+ be connected together to the same power supply with separate bypass capacitors at each V
+
pin.
Note 9:
With the test condition for V
REF
(V
REF
+ V
REF
) given as +4.096V, the 12-bit LSB is 1.0 mV and the 8-bit LSB is 16.0 mV.
Note 10:
Typicals are at T
J
= T
A
= 25C and represent most likely parametric norm.
Note 11:
Tested limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 12:
Positive integral linearity error is defined as the deviation of the analog value, expressed in LSBs, from the straight line that passes through positive
full-scale and zero. For negative integral linearity error, the straight line passes through negative full-scale and zero (see
Figures 2, 3
).
Note 13:
Zero error is a measure of the deviation from the mid-scale voltage (a code of zero), expressed in LSB. It is the worst-case value of the code transitions
between 1 to 0 and 0 to +1 (see
Figure 4
).
Note 14:
Total unadjusted error includes offset, full-scale, linearity and multiplexer errors.
Note 15:
The DC common-mode error is measured in the differential multiplexer mode with the assigned positive and negative input channels shorted together.
Note 16:
Channel leakage current is measured after the channel selection.
Note 17:
Timing specifications are tested at the TTL logic levels, V
IL
= 0.4V for a falling edge and V
IH
= 2.4V for a rising edge. TRI-STATE output voltage is forced
to 1.4V.
Note 18:
The ADC12030 family’s self-calibration technique ensures linearity and offset errors as specified, but noise inherent in the self-calibration process will
result in a maximum repeatability uncertainty of 0.2 LSB.
Note 19:
If SCLK and CCLK are driven from the same clock source, then t
A
is 6, 10, 18 or 34 clock periods minimum and maximum.
Note 20:
The “12-Bit Conversion of Offset” and “12-Bit Conversion of Full-Scale” modes are intended to test the functionality of the device. Therefore, the output
data from these modes are not an indication of the accuracy of a conversion result.
01135410
FIGURE 1. Transfer Characteristic
A
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM4050AI-4.1 | Self-Calibrating 12-Bit Plus Sign Serial I/O A/D Converters with MUX and Sample/Hold |
| LM4120AI-4.1 | Self-Calibrating 12-Bit Plus Sign Serial I/O A/D Converters with MUX and Sample/Hold |
| LM4121AI-4.1 | Self-Calibrating 12-Bit Plus Sign Serial I/O A/D Converters with MUX and Sample/Hold |
| LM432 | Dual Op Amp with On-Chip Fixed 2.5V Reference |
| LM432MA | Dual Op Amp with On-Chip Fixed 2.5V Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4040 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE |
| LM4040/1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Precision Micropower Shunt Voltage Reference |
| LM4040_05 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Precision Micropower Shunt Voltage Reference |
| LM4040_07 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:PRECISION MICROPOWER SHUNT VOLTAGE REFERENCE |
| LM4040_08 | 制造商:ZETEX 制造商全稱:ZETEX 功能描述:Precision micropower shunt voltage references |
發布緊急采購，3分鐘左右您將得到回復。