- 您現在的位置：買賣IC網 > PDF目錄385482 > LM3658SD (NATIONAL SEMICONDUCTOR CORP) Dual Source USB/AC Li Chemistry Charger IC for Portable Applications PDF資料下載
參數資料
| 型號： | LM3658SD |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Dual Source USB/AC Li Chemistry Charger IC for Portable Applications |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, DSO10 |
| 封裝： | 3 X 3 MM, LLP-10 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 663K |
| 代理商： | LM3658SD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁
LM3658 Operation Description
POWER-DOWN MODE
The LM3658 will power down automatically when the voltage
on the USBpwr or CHG_IN pin drops below the battery
voltage with an amount that is equal to V
OK_CHG
(V
BATT
>
V
CC
- V
OK_CHG
). Power-Down mode shuts off the internal
power FETs as well as the open-drain pull-down transistors
on the status pins STAT1 and STAT2. The only current
consumed by the LM3658 is an ultra-low quiescent current
of 1 μA typical.
POWER-ON RESET
As soon as the voltage of one of the power sources rises
above V
+ V
, the charger will wake up. However,
charging will not be initiated unless the supply voltage
source exceeds the V
POR
.
AUTOMATIC POWER SOURCE DETECTION
When the voltage of one of the power sources exceeds the
V
threshold, the LM3658 detects which power source is
a valid charge supply. When both supply voltages are valid
and present, CHG_IN will automatically be selected over
USBpwr. The USBpwr will be the designated power source
only if no CHG_IN is present or when the voltage on the
CHG_IN pin is less than the battery voltage.
THERMAL POWER FET REGULATION
The internal power FETs are thermally regulated to the junc-
tion temperature of 120
o
C to guarantee optimal charging of
the battery. At all times is the charge current limited by the
I
resistor setting, the USB 100 mA/500 mA selection, or
the 100
o
C junction temperature of the LM3658. The charge
current is therefore a function of the charge current settings,
the thermal conductivity of the package and the ambient
temperature as described in the following equation:
20128205
Where T
is the ambient temperature and
θ
is the thermal
resistance of the package. Thermal regulation guarantees
maximum charge current and superior charge rate without
exceeding the power dissipation limits of the LM3658.
PRE-QUALIFICATION MODE
During pre-qualification, STAT1 is on and STAT2 is off, and
the charger supplies a constant current of 50 mA to the
battery. When the battery voltage reaches V
, the
charger transitions from pre-qualification to full-rate charg-
ing. The pre-qualification mode aborts when the battery
doesn’t reach V
within the time allowed in
T
timer. In this event, charging stops and STAT1 and
STAT2 will both be on, indicating a bad battery condition.
CHG_IN FULL-RATE CHARGING MODE
The full-rate charge cycle is initiated following the successful
completion of the pre-qualification mode. Timer T
CHG
starts
to count when the charger enters full-rate charging, with
STAT1 on and STAT2 off. When charging with an AC wall
adapter, the full-rate charge current is proportional to the
value of the resistor that is connected to the I
SET
pin as
described in the following equation:
It is recommended to charge Li-Ion batteries at 1C rate,
where “C” is the capacity of the battery. As an example, it is
recommended to charge a 750 mAh battery at 750 mA, or
1C. Charging at a higher rate can cause damage to the
battery.
USBpwr FULL-RATE CHARGING MODE
The full-rate charge cycle is initiated following the successful
completion of the pre-qualification mode. Timer T
CHG
starts
to count when the charger enters full-rate charging, with
STAT1 on and STAT2 off. If the USB bus provides the
charger supply, then the default full-rate charge current is
100 mA max unless the USB_sel pin is pulled high, which
sets the charge current to 500 mA max.
CONSTANT-VOLTAGE CHARGING MODE AND
END-OF-CHARGE (EOC) DETECTION
The battery voltage increases rapidly as a result of full-rate
charging and will reach the 4.2V termination voltage, trigger-
ing the constant-voltage charge cycle. Timer T
continues
to count in this cycle. STAT1 is on and STAT2 is off. The
charge current gradually decreases during constant-voltage
charging until it reaches the End-Of-Charge (EOC), which is
equal to 10% of the full-rate current set either by the resistor
connected to the I
pin or the USB_sel pin. If Timer T
times out before EOC is reached, charging stops and STAT1
and STAT2 will both be on, indicating a bad battery condition.
TOP-OFF CHARGING MODE
Once EOC has been reached, a top-off cycle continues to
charge the battery. Timed top-off cycle provides optimal
battery capacity following a complete charge cycle. During
this cycle, charging terminates when I
reaches 2.5% of
the full-rate charge current or when T
times out,
whichever occurs first. STAT1 will turn off and STAT2 will turn
on once the top-off cycle completes successfully, indicating
that charging is done.
MAINTENANCE MODE
Maintenance mode begins immediately after the charger
successfully finishes the top-off cycle. In the maintenance
mode, the battery voltage is being monitored by the LM3658
continuously. If the battery voltage drops 200 mV below
V
, a new full-rate charge cycle starts to replenish the
turn on and STAT2 will turn off, and all the timers will reset.
Refer to the LM3658 Flowchart.
CHARGE STATUS OUTPUTS
The LM3658 provides two open-drain outputs STAT1 and
STAT2 that can be connected to external LEDs or to General
Purpose I/O’s (GPIO) of a peripheral IC. All charge status of
the LM3658 is illustrated in
Table 3
. “ON” means that STATx
pin is pulled low as its pull-down transistor is turned on,
representing a logic 0.
L
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LM3658SDX | Dual Source USB/AC Li Chemistry Charger IC for Portable Applications |
| LM3705XBMM-643 | Microprocessor Supervisory Circuits with Power Fail Input, Low Line Output and Manual Reset |
| LM3704XDBP-308 | Microprocessor Supervisory Circuits with Power Fail Input, Low Line Output and Manual Reset |
| LM3704XDBP-643 | Microprocessor Supervisory Circuits with Power Fail Input, Low Line Output and Manual Reset |
| LM3704XDBPX-308 | Microprocessor Supervisory Circuits with Power Fail Input, Low Line Output and Manual Reset |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM3658SD/NOPB | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| LM3658SD-A | 制造商:Texas Instruments 功能描述:Battery Charger Li-Ion/Li-Pol 0mA to 1000mA 4.2V 10-Pin LLP EP T/R 制造商:Texas Instruments 功能描述:BATT CHARGER, LI ION USB/AC, LLP-10 制造商:Texas Instruments 功能描述:Dual Source USB/AC Li Charger,LM3658SD-A |
| LM3658SD-A/NOPB | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| LM3658SD-AEV | 功能描述:電源管理IC開發工具 LM3658 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM3658SD-AEV/NOPB | 功能描述:電池管理 LM3658 Eval Board RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。