參數資料
型號： LM359J
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 運動控制電子
英文描述： Dual, High Speed, Programmable, Current Mode Norton Amplifiers
中文描述： DUAL OP-AMP, 400 MHz BAND WIDTH, CDIP14
封裝： CERAMIC, DIP-14
文件頁數： 10/24頁
文件大?。?/td> 742K
代理商： LM359J
Application Hints
(Continued)
gain in the non-inverting configuration) some external fre-
quency compensation is required because the stray capaci-
tance to ground from the () input and the feedback resistor
add additional lagging phase within the feedback loop. The
value of the input capacitance will typically be in the range of
6 pF to 10 pF for a reasonably constructed circuit board.
When using a feedback resistance of 30 k
or less, the best
method of compensation, without sacrificing slew rate, is to
add a lead capacitor in parallel with the feedback resistor
with a value on the order of 1 pF to 5 pF as shown in Figure
10 .
Another method of compensation is to increase the effective
value of the internal compensation capacitor by adding ca-
pacitance from the COMP pin of an amplifier to ground. An
external 20 pF capacitor will generally compensate for all
gain settings but will also reduce the gain bandwidth product
and the slew rate. These same results can also be obtained
by reducing I
if the full capabilities of the amplifier are
not required. This method is termed over-compensation.
Another area of concern from a stability standpoint is that of
capacitive loading. The amplifier will generally drive capaci-
tive loads up to 100 pF without oscillation problems. Any
larger C loads can be isolated from the output as shown in
Figure 11 Over-compensation of the amplifier can also be
used if the corresponding reduction of the GBW product can
be afforded.
In most applications using the LM359, the input signal will be
AC coupled so as not to affect the DC biasing of the ampli-
fier. This gives rise to another subtlety of high frequency cir-
cuits which is the effective series inductance (ESL) of the
coupling capacitor which creates an increase in the imped-
ance of the capacitor at high frequencies and can cause an
unexpected gain reduction. Low ESL capacitors like solid
tantalum for large values of C and ceramic for smaller values
are recommended. A parallel combination of the two types is
even better for gain accuracy over a wide frequency range.
AMPLIFIER DESIGN EXAMPLES
The ability of the LM359 to provide gain at frequencies
higher than most monolithic amplifiers can provide makes it
most useful as a basic broadband amplification stage. The
design of standard inverting and non-inverting amplifiers,
though different than standard op amp design due to the cur-
rent differencing inputs, also entail subtle design differences
between the two types of amplifiers. These differences will
be best illustrated by design examples. For these examples
a practical video amplifier with a passband of 8 Hz to 10 MHz
and a gain of 20 dB will be used. It will be assumed that the
input will come from a 75
source and proper signal termi-
nation will be considered. The supply voltage is 12 V
and
single resistor programming of the operating current, I
SET
,
will be used for simplicity.
AN INVERTING VIDEO AMPLIFIER
1.
Basic circuit configuration:
2.
Determine the required I
from the characteristic
curves for gain bandwidth product.
GBW
= 10 x 10 MHz = 100 MHz
For a flat response to 10 MHz a closed loop response to two
octaves above 10 MHz (40 MHz) will be sufficient.
Actual GBW = 10 x 40 MHz = 400 MHz
I
SET
required = 0.5 mA
DS007788-15
C
f
= 1 pF to 5 pF for stability
FIGURE 10. Best Method of Compensation
DS007788-16
FIGURE 11. Isolating Large Capacitive Loads
DS007788-17
www.national.com
10
相關PDF資料
PDF描述
LM359M Dual, High Speed, Programmable, Current Mode Norton Amplifiers
LM359N Dual, High Speed, Programmable, Current Mode Norton Amplifiers
LM3647IM Universal Battery Charger for Li-Ion, Ni-MH and Ni-Cd Batteries
LM3647 Universal Battery Charger for Li-Ion, Ni-MH and Ni-Cd Batteries
LM3658 Dual Source USB/AC Li Chemistry Charger IC for Portable Applications
相關代理商/技術參數
參數描述
LM359M 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
LM359M/NOPB 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
LM359MX 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
LM359MX/NOPB 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel
LM359N 制造商:Panasonic Industrial Company 功能描述:IC 制造商:OC White Company 功能描述:SP Amp DIFF AMP Dual 22V 14-Pin PDIP Rail
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*