參數資料
型號： LM2831ZMF
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 穩壓器
英文描述： High Frequency 1.5A Load - Step-Down DC-DC Regulator
中文描述： 2.5 A SWITCHING REGULATOR, 3750 kHz SWITCHING FREQ-MAX, PDSO5
封裝： SOT-23, 5 PIN
文件頁數： 13/27頁
文件大?。?/td> 893K
代理商： LM2831ZMF
Design Guide
(Continued)
significantly with little detriment to the regulator stability. Like
the input capacitor, recommended multilayer ceramic ca-
pacitors are X7R or X5R types.
CATCH DIODE
The catch diode (D1) conducts during the switch off-time. A
Schottky diode is recommended for its fast switching times
and low forward voltage drop. The catch diode should be
chosen so that its current rating is greater than:
I
D1
= I
OUT
x (1-D)
The reverse breakdown rating of the diode must be at least
the maximum input voltage plus appropriate margin. To im-
prove efficiency, choose a Schottky diode with a low forward
voltage drop.
OUTPUT VOLTAGE
The output voltage is set using the following equation where
R2 is connected between the FB pin and GND, and R1 is
connected between V
and the FB pin. A good value for R2
is 10k. When designing a unity gain converter (Vo = 0.6V),
R1 should be between 0
and 100
, and R2 should be
equal or greater than 10k
.
V
REF
= 0.60V
PCB LAYOUT CONSIDERATIONS
When planning layout there are a few things to consider
when trying to achieve a clean, regulated output. The most
important consideration is the close coupling of the GND
connections of the input capacitor and the catch diode D1.
These ground ends should be close to one another and be
connected to the GND plane with at least two through-holes.
Place these components as close to the IC as possible. Next
in importance is the location of the GND connection of the
output capacitor, which should be near the GND connections
of CIN and D1. There should be a continuous ground plane
on the bottom layer of a two-layer board except under the
switching node island. The FB pin is a high impedance node
and care should be taken to make the FB trace short to avoid
noise pickup and inaccurate regulation. The feedback resis-
tors should be placed as close as possible to the IC, with the
GND of R1 placed as close as possible to the GND of the IC.
The V
OUT
trace to R2 should be routed away from the
inductor and any other traces that are switching. High AC
currents flow through the V
IN
, SW and V
OUT
traces, so they
should be as short and wide as possible. However, making
the traces wide increases radiated noise, so the designer
must make this trade-off. Radiated noise can be decreased
by choosing a shielded inductor. The remaining components
should also be placed as close as possible to the IC. Please
see Application Note AN-1229 for further considerations and
the LM2831 demo board as an example of a four-layer
layout.
L
www.national.com
13
相關PDF資料
PDF描述
LM2831ZMFX High Frequency 1.5A Load - Step-Down DC-DC Regulator
LM2831ZSD High Frequency 1.5A Load - Step-Down DC-DC Regulator
LM2831ZSDX High Frequency 1.5A Load - Step-Down DC-DC Regulator
LM2832ZSD High Frequency 2.0A Load - Step-Down DC-DC Regulator
LM2832 High Frequency 2.0A Load - Step-Down DC-DC Regulator
相關代理商/技術參數
參數描述
LM2831ZMF EVAL 功能描述:電源管理IC開發工具 LM2831 Eval Brd RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
LM2831ZMF 制造商:Texas Instruments 功能描述:IC V REG 1.5A 3MHZ BUCK SMD 2831
LM2831ZMF/NOPB 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
LM2831ZMFEVAL 制造商:Texas Instruments 功能描述:
LM2831ZMFX 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*