- 您現在的位置：買賣IC網 > PDF目錄385478 > LM2830ZSD (NATIONAL SEMICONDUCTOR CORP) High Frequency 1.0A Load - Step-Down DC-DC Regulator PDF資料下載
參數資料
| 型號： | LM2830ZSD |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | High Frequency 1.0A Load - Step-Down DC-DC Regulator |
| 中文描述： | 1.75 A SWITCHING REGULATOR, 3750 kHz SWITCHING FREQ-MAX, PDSO6 |
| 封裝： | LLP-6 |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 862K |
| 代理商： | LM2830ZSD |
Design Guide
(Continued)
In general,
i
L
= 0.1 x (I
OUT
)
→
0.2 x (I
OUT
)
If
i
L
= 20% of 1A, the peak current in the inductor will be
1.2A. The minimum guaranteed current limit over all operat-
ing conditions is 1.2A. One can either reduce
i
, or make
the engineering judgment that zero margin will be safe
enough. The typical current limit is 1.75A.
The LM2830 operates at frequencies allowing the use of
ceramic output capacitors without compromising transient
response. Ceramic capacitors allow higher inductor ripple
without significantly increasing output ripple. See the output
capacitor section for more details on calculating output volt-
age ripple. Now that the ripple current is determined, the
inductance is calculated by:
Where
When selecting an inductor, make sure that it is capable of
supporting the peak output current without saturating. Induc-
tor saturation will result in a sudden reduction in inductance
and prevent the regulator from operating correctly. Because
of the speed of the internal current limit, the peak current of
the inductor need only be specified for the required maxi-
mum output current. For example, if the designed maximum
output current is 1.0Aand the peak current is 1.25A, then the
inductor should be specified with a saturation current limit of
>
1.25A. There is no need to specify the saturation or peak
current of the inductor at the 1.75A typical switch current
limit. The difference in inductor size is a factor of 5. Because
of the operating frequency of the LM2830, ferrite based
inductors are preferred to minimize core losses. This pre-
sents little restriction since the variety of ferrite-based induc-
tors is huge. Lastly, inductors with lower series resistance
(R
) will provide better operating efficiency. For recom-
mended inductors see Example Circuits.
INPUT CAPACITOR
An input capacitor is necessary to ensure that V
does not
drop excessively during switching transients. The primary
specifications of the input capacitor are capacitance, volt-
age, RMS current rating, and ESL (Equivalent Series Induc-
tance). The recommended input capacitance is 22 μF.The
input voltage rating is specifically stated by the capacitor
manufacturer. Make sure to check any recommended derat-
ings and also verify if there is any significant change in
capacitance at the operating input voltage and the operating
temperature. The input capacitor maximum RMS input cur-
rent rating (I
RMS-IN
) must be greater than:
Neglecting inductor ripple simplifies the above equation to:
It can be shown from the above equation that maximum
RMS capacitor current occurs when D = 0.5. Always calcu-
late the RMS at the point where the duty cycle D is closest to
0.5. The ESL of an input capacitor is usually determined by
the effective cross sectional area of the current path. A large
leaded capacitor will have high ESL and a 0805 ceramic chip
capacitor will have very low ESL. At the operating frequen-
cies of the LM2830, leaded capacitors may have an ESL so
large that the resulting impedance (2
π
fL) will be higher than
that required to provide stable operation. As a result, surface
mount capacitors are strongly recommended.
Sanyo POSCAP, Tantalum or Niobium, Panasonic SP, and
multilayer ceramic capacitors (MLCC) are all good choices
for both input and output capacitors and have very low ESL.
For MLCCs it is recommended to use X7R or X5R type
capacitors due to their tolerance and temperature character-
istics. Consult capacitor manufacturer datasheets to see
how rated capacitance varies over operating conditions.
OUTPUT CAPACITOR
The output capacitor is selected based upon the desired
output ripple and transient response. The initial current of a
load transient is provided mainly by the output capacitor. The
output ripple of the converter is:
When using MLCCs, the ESR is typically so low that the
capacitive ripple may dominate. When this occurs, the out-
put ripple will be approximately sinusoidal and 90 phase
shifted from the switching action. Given the availability and
quality of MLCCs and the expected output voltage of designs
using the LM2830, there is really no need to review any other
capacitor technologies. Another benefit of ceramic capaci-
tors is their ability to bypass high frequency noise. A certain
amount of switching edge noise will couple through parasitic
capacitances in the inductor to the output. A ceramic capaci-
tor will bypass this noise while a tantalum will not. Since the
output capacitor is one of the two external components that
control the stability of the regulator control loop, most appli-
cations will require a minimum of 22 μF of output capaci-
tance. Capacitance often, but not always, can be increased
20197405
FIGURE 3. Inductor Current
L
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM2830ZSDX | High Frequency 1.0A Load - Step-Down DC-DC Regulator |
| LM2831 | High Frequency 1.5A Load - Step-Down DC-DC Regulator |
| LM2831XMF | High Frequency 1.5A Load - Step-Down DC-DC Regulator |
| LM2831XMFX | High Frequency 1.5A Load - Step-Down DC-DC Regulator |
| LM2831XSD | High Frequency 1.5A Load - Step-Down DC-DC Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2830ZSD/NOPB | 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| LM2830ZSDX | 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| LM2830ZSDX/NOPB | 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| LM2831 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Frequency 1.5A Load - Step-Down DC-DC Regulator |
| LM2831XMF | 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。