- 您現在的位置：買賣IC網 > PDF目錄385477 > LM2753SDX (NATIONAL SEMICONDUCTOR CORP) High Power Switched Capacitor Voltage Convertor/Flash LED Driver PDF資料下載
參數資料
| 型號： | LM2753SDX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 顯示驅動器 |
| 英文描述： | High Power Switched Capacitor Voltage Convertor/Flash LED Driver |
| 中文描述： | LED DISPLAY DRIVER, DSO10 |
| 封裝： | 3 X 3 MM, 0.80 MM HEIGHT, LLP-10 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 520K |
| 代理商： | LM2753SDX |
Application Information
CIRCUIT DESCRIPTION
The LM2753 is a Switched Capacitor Doubler with a regu-
lated 5V output. It is capable of continuously supplying up to
200mA at 5V to a load connected to V
. This device uses
Pulse Frequency Modulation and a Multi-Level Switch Array
to regulate and maintain the output voltage. For higher load
currents, such as during Flash operation, the output voltage
is allowed to droop to supply the necessary current.Although
there is no current limit on this device, the device will auto-
matically default to a gain of 1 when the output is brought
below the input voltage. This configuration limits the input
current to about 300mA (typ.). The operating range for the
LM2753 is over the extended Li-Ion battery range from 2.7V
to 5.5V.
Aside from powering Flash LEDs, the LM2753 is suitable for
driving other devices with power requirements up to 200mA.
White LEDs can also be connected to this device to backlight
a cellular phone keypad and display. The LED brightness
can be controlled by applying a PWM (Pulse Width Modula-
tion) signal to the Enable pin (EN) during "Torch" mode, or to
the Flash pin during "Flash" mode. (see
PWM BRIGHT-
NESS CONTROL PROCEDURES
section).
SOFT START
Soft Start is engaged when the device is taken out of Shut-
down mode (EN = logic HIGH) or when voltage is supplied
simultaneously to the VIN and EN pins. During Soft Start, the
voltage on V
will ramp up in proportion to the rate that the
reference voltage is being ramped up. The output voltage is
programmed to rise from 0V to 5V in 640μs (typ.).
ENABLE MODE
The Enable logic pin (EN) disables the part and reduces the
quiescent current to 0.1μA(typ.). The LM2753 has an active-
high enable pin (LOW = shut down, HIGH = operating). The
LM2753 EN pin can be driven with a low-voltage CMOS logic
signal (1.5V logic, 1.8V logic, etc). There is an internal
300k
pull-down resistor between the EN and GND pins of
the LM2753.
FLASH MODE
The Flash logic pin (Flash) controls the internal FET con-
nected between the V
and I
pins on the LM2753. The
LM2753 has an active-HIGH Flash pin (LOW = shut down,
HIGH = operating). A logic HIGH signal must be present on
the EN pin before a logic HIGH signal is place on the Flash
input pin. The EN and Flash input pins can be connected
together and controlled with the same logic signal. The
turn-on time for I
in this configuration will be limited by
the turn-on time of the device. The turn-on time for the
internal FET is typically 10ns when the device is already on
(EN signal HIGH, V
at 5V). The LM2753 Flash pin can be
driven with a low-voltage CMOS logic signal (1.5V logic,
1.8V logic, etc). There is an internal 300k
pull-down resis-
tor between the Flash and GND pins of the LM2753.
CAPACITOR SELECTION
The LM2753 requires 3 external capacitors for proper opera-
tion. Surface-mount multi-layer ceramic capacitors are rec-
ommended. These capacitors are small, inexpensive and
have very low equivalent series resistance (ESR,
≤
15m
typ.). Tantalum capacitors, OS-CON capacitors, and alumi-
num electrolytic capacitors are generally not recommended
for use with the LM2753 due to their high ESR, as compared
to ceramic capacitors.
For most applications, ceramic capacitors with X7R or X5R
temperature characteristic are preferred for use with the
LM2753. These capacitors have tight capacitance tolerance
(as good as
±
10%), hold their value over temperature (X7R:
±
15% over 55C to 125C; X5R:
±
15% over 55C to
85C), and typically have little voltage coefficient when com-
pared to other types of capacitors. However selecting a
capacitor with a voltage rating much higher than the voltage
it will be subjected to, will ensure that the capacitance will
stay closer to the capacitor’s nominal value. Capacitors with
Y5V or Z5U temperature characteristic are generally not
recommended for use with the LM2753. Capacitors with
these temperature characteristics typically have wide ca-
pacitance tolerance (+80%, 20%), vary significantly over
temperature (Y5V: +22%, 82% over 30C to +85C range;
Z5U: +22%, 56% over +10C to +85C range), and have
poor voltage coefficients. Under some conditions, a nominal
1μF Y5V or Z5U capacitor could have a capacitance of only
0.1μF. Such detrimental deviation is likely to cause Y5V and
Z5U capacitors to fail to meet the minimum capacitance
requirements of the LM2753.
Table 1
lists suggested capaci-
tor suppliers for the typical application circuit.
TABLE 1. Ceramic Capacitor Manufacturers
Manufacturer
TDK
Murata
Taiyo Yuden
Contact
www.component.tdk.com
www.murata.com
www.t-yuden.com
FLASH LED SELECTION
The LM2753 provides a 5V (typ.) fixed voltage to drive a
Flash LED with a continuous current up to 200mA (typ.). At
LED currents above 200mA (typ.), the output of the LM2753
is allowed to droop to deliver the desired current to the Flash
LED. This droop limits the maximum forward voltage and in
turn the maximum current that can be supplied to a given
LED. LEDs should be chosen such that the LED forward
voltage at the desired maximum LED current does not ex-
ceed the output voltage of the LM2753 when loaded down
with that same current. It is suggested that the selected
LEDs be binned due to the relatively high forward voltage
tolerance of Flash LEDs. The typical and maximum diode
forward voltage depends highly on the manufacturer and
their technology.
Table 2
lists several suggested manufac-
turers.
TABLE 2. Flash LED Selection
Manufacturer
Agilent
AOT
Citizen
Lumiled
Nichia
Osram
Panasonic
Seoul Semiconductor
Contact
www.agilent.com/semiconductors
www.aot.com.tw
www.c-e.co.jp/e/
www.lumileds.com
www.nichia.com
www.osram-os.com
www.panasonic.co.jp/semicon/
en.seoulsemicon.co.kr
L
www.national.com
5
相關PDF資料 |
PDF描述 |
|---|---|
| LM2765 | Switched Capacitor Voltage Converter |
| LM2765M6 | Switched Capacitor Voltage Converter |
| LM2765M6X | Switched Capacitor Voltage Converter |
| LM2781 | Ultra-Low Ripple Switched Capacitor Voltage Inverter |
| LM2781TP | Ultra-Low Ripple Switched Capacitor Voltage Inverter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2753SDX/NOPB | 功能描述:LED照明驅動器 RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| LM2754 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:800mA Switched Capacitor Flash LED Driver with Time-Out Protection |
| LM2754SQ | 功能描述:LED照明驅動器 RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| LM2754SQ | 制造商:Texas Instruments 功能描述:LED DRIVER CHARGE PUMP POWERWISE |
| LM2754SQ/NOPB | 功能描述:LED照明驅動器 RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。