- 您現在的位置：買賣IC網 > PDF目錄385477 > LM2707MF (NATIONAL SEMICONDUCTOR CORP) Inductive-Boost Series LED Driver with Programmable Oscillator Frequency PDF資料下載
參數資料
| 型號： | LM2707MF |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 顯示驅動器 |
| 英文描述： | Inductive-Boost Series LED Driver with Programmable Oscillator Frequency |
| 中文描述： | LED DISPLAY DRIVER, PDSO8 |
| 封裝： | SOT-23, 8 PIN |
| 文件頁數： | 14/19頁 |
| 文件大小： | 1039K |
| 代理商： | LM2707MF |
Components and Connectivity
(Continued)
C
. These capacitors have tight capacitance tolerance (as
good as +/-10%) and hold their value over temperature
(X7R: +/-15% over –55C to 125C; X5R: +/-15% over
–55C to 85C).
Capacitors with a Y5V or Z5U temperature characteristic are
generally not recommended for use with the LM2707. These
types of capacitors typically have wide capacitance toler-
ance (+80%, -20%) and vary significantly over temperature
(Y5V: +22%, -82% over –30C to +85C; Z5U: +22%, -56%
over +10C to +85C). Under some conditions, a 1uF-rated
Y5V or Z5U capacitor could have a capacitance as low as
0.1uF. The greatly reduced capacitance under some condi-
tions will result in very high ripple voltages and currents.
Net capacitance of a ceramic capacitor decreases with in-
creased DC bias. This capacitance reduction can give lower
capacitance than expected on the input and/or output, result-
ing in higher ripple voltages and currents. Using capacitors
at DC bias voltages significantly below the capacitor voltage
rating will usually minimize DC bias effects. Consult capaci-
tor manufacturers for information on capacitor DC bias char-
acteristics.
A ceramic capacitor can also be used for the C
capacitor. A
small capacitor with a good temperature coefficient (COG,
for example) should be chosen.
Below is a list of some leading ceramic capacitor manufac-
turers:
TDK
<
www.component.tdk.com
AVX
<
www.avx.com
>
Murata
<
www.murata.com
>
Taiyo Yuden
<
www.t-yuden.com
>
Vishay
<
www.vishay.com
>
BOARD LAYOUT RECOMMENDATIONS
For optimal LM2707 circuit performance, the following board
layout suggestions are recommended:
Use short, wide traces and/or fills to connect the LM2707
and the external components. This results in low imped-
ance connections that minimize parasitic losses and
noise emissions.
Utilize low impedance traces and an internal ground
plane to connect the LM2707 GND pin to the input ca-
pacitor, output capacitor, C
X
capacitor, and feedback re-
sistor.
Place the input capacitor as close to the LM2707 V
IN
pin
as possible to minimize input noise.
Place the inductor and rectifier diode as close as possible
to the SW pin and minimize the lengths of the connec-
tions of this high-frequency switching node.
See
Figure 9
for an example of a recommended board layout
of an LM2707 circuit.
Application Information
LED DRIVE EFFICIENCY
The LM2707 can be used to build a high efficiency LED drive
circuit. The low ON resistance of the NFET power device and
the sub-bandgap feedback voltage minimize the power con-
sumption of the LED-drive circuit. A circuit that uses an
inductor with a low series resistance and a diode with a low
forward voltage (low-V
F
) will achieve maximum LED drive
efficiency.
LED drive efficiency (E) is commonly measured and calcu-
lated by taking the ratio of power consumed by the LEDs to
the power consumed at the input of the LED drive circuit:
Efficiency curves for a representative LM2707 LED drive
circuits can be referenced in the
Typical Performance Char-
acteristics
graphs.
LED BRIGHTNESS ADJUSTMENT
There are several methods and application circuits that can
be used to dynamically adjust LED brightness.
A pulse-width modulated signal applied to the enable (EN)
pin can be used to strobe the LEDs and adjust the perceived
LED brightness (see the schematic on page 1 of the
datasheet). With this approach, the LEDs are ON and driven
at the current programmed by the feedback resistor when
the pulse voltage is high. The LM2707 and the LEDs are
OFF when the pulse voltage is low. Brightness is propor-
tional to the duty cycle of the pulse signal.
The LM2707 can accommodate a very wide range of PWM
signal frequencies: signals between 100Hz and 50kHz are
acceptable. Signals below 100Hz are not recommended
because these lower frequencies are distinguishable by the
human eye. The brightness vs. duty cycle characteristic of
the circuit may vary slightly with different PWM frequencies.
This is especially noticable at the higher PWM frequencies.
See
Table 1
for an example.
20099234
FIGURE 9. Example LM2707 LED Driver Board Layout
(LEDs not shown)
L
www.national.com
14
相關PDF資料 |
PDF描述 |
|---|---|
| LM2707MFX | Inductive-Boost Series LED Driver with Programmable Oscillator Frequency |
| LM2720 | 5-Bit Programmable, High Frequency Multi-phase PWM Controller |
| LM2720M | RES, 10K0 .125W 1% SMT, 0805 |
| LM2722 | High Speed Synchronous/Asynchronous MOSFET Driver |
| LM2722MX | High Speed Synchronous/Asynchronous MOSFET Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2707MF/NOPB | 功能描述:IC LED DRVR WHITE BCKLGT SOT23-8 RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:1 系列:- 恒定電流:- 恒定電壓:- 拓撲:PWM，切換式電容器（充電泵） 輸出數:1 內部驅動器:是 類型 - 主要:背光 類型 - 次要:白色 LED 頻率:642kHz 電源電壓:2.7 V ~ 5.5 V 輸出電壓:5V 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-VSON 包裝:剪切帶 (CT) 工作溫度:-30°C ~ 85°C 產品目錄頁面:1371 (CN2011-ZH PDF) 其它名稱:BD1603NUV-E2CT |
| LM2707MFX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Inductive-Boost Series LED Driver with Programmable Oscillator Frequency |
| LM2707MFX/NOPB | 功能描述:IC LED DRVR WHITE BCKLGT SOT23-8 RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:1 系列:- 恒定電流:- 恒定電壓:- 拓撲:PWM，切換式電容器（充電泵） 輸出數:1 內部驅動器:是 類型 - 主要:背光 類型 - 次要:白色 LED 頻率:642kHz 電源電壓:2.7 V ~ 5.5 V 輸出電壓:5V 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-VSON 包裝:剪切帶 (CT) 工作溫度:-30°C ~ 85°C 產品目錄頁面:1371 (CN2011-ZH PDF) 其它名稱:BD1603NUV-E2CT |
| LM2708HTLX-1.57/NOPB | 制造商:Texas Instruments 功能描述: |
| LM270WF5-SLM1 | 制造商:LG.Philips Lcd 功能描述:27" FHD,1920X1080,250 NITS, LVDS, 72% IPS - Bulk |
發布緊急采購，3分鐘左右您將得到回復。