![](http://datasheet.mmic.net.cn/70000/LM2577TADJFLOWLB03_datasheet_2335570/LM2577TADJFLOWLB03_17.png)
Application Hints (Continued)
3. Output Voltage Selection (R1 and R2)
This section is for applications using the LM1577-ADJ/
LM2577-ADJ. Skip this section if the LM1577-12/LM2577-12
or LM1577-15/LM2577-15 is being used.
With the LM1577-ADJ/LM2577-ADJ, the output voltage is
given by
V
OUT = 1.23V (1 + R1/R2)
Resistors R1 and R2 divide the output down so it can be
compared
with
the
LM1577-ADJ/LM2577-ADJ
internal
1.23V reference. For a given desired output voltage V
OUT,
select R1 and R2 so that
4. Input Capacitor Selection (C
IN)
The switching action in the step-up regulator causes a trian-
gular ripple current to be drawn from the supply source. This
in turn causes noise to appear on the supply voltage. For
proper operation of the LM1577, the input voltage should be
decoupled. Bypassing the Input Voltage pin directly to
ground with a good quality, low ESR, 0.1 F capacitor (leads
as short as possible) is normally sufficient.
If the LM1577 is located far from the supply source filter ca-
pacitors, an additional large electrolytic capacitor (e.g.
47 F) is often required.
5. Diode Selection (D)
The switching diode used in the boost regulator must with-
stand a reverse voltage equal to the circuit output voltage,
and must conduct the peak output current of the LM2577. A
suitable diode must have a minimum reverse breakdown
voltage greater than the circuit output voltage, and should be
rated for average and peak current greater than I
LOAD(max)
and I
D(PK). Schottky barrier diodes are often favored for use
in switching regulators. Their low forward voltage drop allows
higher regulator efficiency than if a (less expensive) fast re-
covery diode was used. See
Figure 12 for recommended
part numbers and voltage ratings of 1A and 3A diodes.
BOOST REGULATOR CIRCUIT EXAMPLE
By adding a few external components (as shown in
Figure
13), the LM2577 can be used to produce a regulated output
voltage that is greater than the applied input voltage. Typical
performance of this regulator is shown in
Figure 14 and Fig-
ure 15. The switching waveforms observed during the opera-
tion of this circuit are shown in
Figure 16.
Cornell Dublier — Types 239, 250, 251, UFT,
300, or 350
P.O. Box 128, Pickens, SC 29671
(803) 878-6311
Nichicon — Types PF, PX, or PZ
927 East Parkway,
Schaumburg, IL 60173
(708) 843-7500
Sprague — Types 672D, 673D, or 674D
Box 1, Sprague Road,
Lansing, NC 28643
(919) 384-2551
United Chemi-Con — Types LX, SXF, or SXJ
9801 West Higgins Road,
Rosemont, IL 60018
(708) 696-2000
FIGURE 11. Aluminum Electrolytic Capacitors
Recommended for Switching Regulators
V
OUT
Schottky
Fast Recovery
(max)
1A
3A
1A
3A
20V
1N5817
1N5820
MBR120P
MBR320P
1N5818
1N5821
30V
MBR130P
MBR330P
11DQ03
31DQ03
1N5819
1N5822
40V
MBR140P
MBR340P
11DQ04
31DQ04
MBR150
MBR350
1N4933
50V
11DQ05
31DQ05
MUR105
1N4934
MR851
100V
HER102
30DL1
MUR110
MR831
10DL1
HER302
FIGURE 12. Diode Selection Chart
www.national.com
17