![](http://datasheet.mmic.net.cn/30000/LM2576T-ADJFLOWLB03_datasheet_2335552/LM2576T-ADJFLOWLB03_6.png)
All Output Voltage Versions
Electrical Characteristics (Continued)
Specifications with standard type face are for T
J = 25C, and those with boldface type apply over full Operating Temperature
Range. Unless otherwise specified, V
IN = 12V for the 3.3V, 5V, and Adjustable version, VIN = 25V for the 12V version, and VIN
= 30V for the 15V version. I
LOAD = 500 mA.
Symbol
Parameter
Conditions
LM2576-XX
Units
(Limits)
LM2576HV-XX
Typ
Limit
DEVICE PARAMETERS
θ
JA
Thermal Resistance
65
θ
JA
45
C/W
θ
JC
T Package, Junction to Case
2
θ
JA
50
V
IH
ON /OFF Pin
V
OUT = 0V
1.4
2.2/2.4
V(Min)
V
IL
Logic Input Level
V
OUT = Nominal Output Voltage
1.2
1.0/0.8
V(Max)
I
IH
ON /OFF Pin Input
ON /OFF Pin = 5V (OFF)
12
A
Current
30
A(Max)
I
IL
ON /OFF Pin = 0V (ON)
0A
10
A(Max)
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics.
Note 2: All limits guaranteed at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits are 100%
production tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods.
Note 3: External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance. When the
LM2576/LM2576HV is used as shown in the
Figure 2 test circuit, system performance will be as shown in system parameters section of Electrical Characteristics.
Note 4: Output pin sourcing current. No diode, inductor or capacitor connected to output.
Note 5: Feedback pin removed from output and connected to 0V.
Note 6: Feedback pin removed from output and connected to +12V for the Adjustable, 3.3V, and 5V versions, and +25V for the 12V and 15V versions, to force the
output transistor OFF.
Note 7: VIN = 40V (60V for high voltage version).
Note 8: Junction to ambient thermal resistance (no external heat sink) for the 5 lead TO-220 package mounted vertically, with 12 inch leads in a socket, or on a PC
board with minimum copper area.
Note 9: Junction to ambient thermal resistance (no external heat sink) for the 5 lead TO-220 package mounted vertically, with 14 inch leads soldered to a PC board
containing approximately 4 square inches of copper area surrounding the leads.
Note 10: If the TO-263 package is used, the thermal resistance can be reduced by increasing the PC board copper area thermally connected to the package. Using
0.5 square inches of copper area,
θJA is 50C/W, with 1 square inch of copper area, θJA is 37C/W, and with 1.6 or more square inches of copper area, θJA is 32C/W.
Note 11: The oscillator frequency reduces to approximately 11 kHz in the event of an output short or an overload which causes the regulated output voltage to drop
approximately 40% from the nominal output voltage. This self protection feature lowers the average power dissipation of the IC by lowering the minimum duty cycle
from 5% down to approximately 2%.
Typical Performance Characteristics
Normalized Output Voltage
Line Regulation
01147627
01147628
LM2576/LM2576HV
www.national.com
6