參數資料
型號: LM2471TA
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 音頻/視頻放大
英文描述: Monolithic Triple 4 ns High Swing CRT Driver
中文描述: 1 CHANNEL, VIDEO AMPLIFIER, PZFM11
封裝: PLASTIC, TO-220, 11 PIN
文件頁數: 5/10頁
文件大?。?/td> 663K
代理商: LM2471TA
Theory of Operation
The LM2471 is a high voltage monolithic three channel CRT
driver suitable for high resolution display applications. The
LM2471 operates with 85V and 8V power supplies. The part
is housed in the industry standard 11-lead TO-220 molded
plastic power package.
The circuit diagram of the LM2471 is shown in
Figure 1
. The
PNP emitter follower, Q5, provides input buffering. Q1 and
Q2 form a fixed gain cascode amplifier with resistors R1 and
R2 setting the gain at 27. Emitter followers Q3 and Q4
isolate the high output impedance of the cascode stage from
the capacitance of the CRT cathode which decreases the
sensitivity of the device to load capacitance. Q6 provides
biasing to the output emitter follower stage to reduce cross-
over distortion at low signal levels.
Figure 2
shows a typical test circuit for evaluation of the
LM2471. This circuit is designed to allow testing of the
LM2471 in a 50
environment without the use of an expen-
sive FET probe. In this test circuit, the two 2.49k
resistors
form a 200:1 wideband, low capacitance probe when con-
nected to a 50
coaxial cable and a 50
load (such as a
50
oscilloscope input). The input signal from the generator
is ac coupled to the base of Q5.
Application Hints
INTRODUCTION
National Semiconductor (NSC) is committed to provide ap-
plication information that assists our customers in obtaining
the best performance possible from our products. The fol-
lowing information is provided in order to support this com-
mitment. The reader should be aware that the optimization of
performance was done using a specific printed circuit board
designed at NSC. Variations in performance can be realized
due to physical changes in the printed circuit board and the
application. Therefore, the designer should know that com-
ponent value changes may be required in order to optimize
performance in a given application. The values shown in this
document can be used as a starting point for evaluation
purposes. When working with high bandwidth circuits, good
layout practices are also critical to achieving maximum per-
formance.
IMPORTANT INFORMATION
The LM2471 performance is targeted for the VGA (640 x
480) to UXGA (1600 x 1200, 70Hz) resolution market. The
application circuits shown in this document to optimize per-
formance and to protect against damage from CRT arcover
are designed specifically for the LM2471. If another member
of the LM247X family is used, please refer to its datasheet.
POWER SUPPLY BYPASS
Since the LM2471 is a wide bandwidth amplifier, proper
power supply bypassing is critical for optimum performance.
Improper power supply bypassing can result in large over-
shoot, ringing or oscillation. 0.1 μF capacitors should be
connected from the supply pins, V
CC
and V
BB
, to ground, as
close to the LM2471 as is practical. Additionally, a 47 μF or
larger electrolytic capacitor should be connected from both
supply pins to ground reasonably close to the LM2471.
ARC PROTECTION
During normal CRT operation, internal arcing may occasion-
ally occur. Spark gaps, in the range of 200V, connected from
the CRT cathodes to CRT ground will limit the maximum
voltage, but to a value that is much higher than allowable on
the LM2471. This fast, high voltage, high energy pulse can
damage the LM2471 output stage. The application circuit
shown in
Figure 9
is designed to help clamp the voltage at
the output of the LM2471 to a safe level. The clamp diodes,
D1 and D2, should have a fast transient response, high peak
current rating, low series impedance and low shunt capaci-
tance. FDH400 or equivalent diodes are recommended. Do
not use 1N4148 diodes for the clamp diodes. D1 and D2
should have short, low impedance connections to V
and
ground respectively. The cathode of D1 should be located
very close to a separately decoupled bypass capacitor (C3 in
Figure 9
). The ground connection of D2 and the decoupling
capacitor should be very close to the LM2471 ground. This
will significantly reduce the high frequency voltage transients
that the LM2471 would be subjected to during an arcover
condition. Resistor R2 limits the arcover current that is seen
by the diodes while R1 limits the current into the LM2471 as
well as the voltage stress at the outputs of the device. R2
should be a
1
2
W solid carbon type resistor. R1 can be a
1
4
W
metal or carbon film type resistor. Having large value resis-
tors for R1 and R2 would be desirable, but this has the effect
of increasing rise and fall times. Inductor L1 is critical to
reduce the initial high frequency voltage levels that the
LM2471 would be subjected to. The inductor will not only
help protect the device but it will also help minimize rise and
fall times as well as minimize EMI. For proper arc protection,
it is important to not omit any of the arc protection compo-
nents shown in
Figure 9
.
L
www.national.com
5
相關PDF資料
PDF描述
LM258H Octal Buffers/Drivers With 3-State Outputs 20-SO -40 to 85
LM2633 Advanced Two-Phase Synchronous Triple Regulator Controller for Notebook CPUs
LM2633MTD Advanced Two-Phase Synchronous Triple Regulator Controller for Notebook CPUs
LM2647LQX Dual Synchronous Buck Regulator Controller
LM2647MTC Dual Synchronous Buck Regulator Controller
相關代理商/技術參數
參數描述
LM2476 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Monolithic Triple Channel 6.5 ns High Gain CRT Driver and Bias Clamp
LM2476TB 功能描述:顯示驅動器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
LM2476TB/NOPB 功能描述:顯示驅動器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
LM2479 制造商:NSC 制造商全稱:National Semiconductor 功能描述:120V Triple Bias Clamp
LM2479BN WAF 制造商:Texas Instruments 功能描述: